Accessories; Optional Features (Field Installed - Lincoln Electric CLASSIC 300 D Operator's Manual

C-1
OPTIONAL FEATURES
GENERAL OPTIONS
WARNING
Pipe Thawing with an arc welder can cause fire,
explosion, damage to electric wiring or to the arc
welder if done improperly. The use of an arc
welder for pipe thawing is not approved by the
CSA, nor is it recommended or supported by
Lincoln Electric.
------------------------------------------------------------------------
Power Plug Kit (K802D) - A power plug kit for the
auxiliary power receptacles is available. (Provides a
plug for each receptacle.)
GFCI Receptacle Kit (K1690-1) - Includes one UL
approved 115V ground fault circuit interrupter duplex
type receptacle with cover and installation instruc-
tions. Replaces the factory installed 115V duplex
receptacle. Each receptacle of the GFCI duplex is
rated at 20 amps. Maximum total current from the
GFCI duplex is limited to 20 amps. See the MAINTE-
NANCE section for detailed information on testing and
resetting the GFCI receptacle.
Spark Arrestor Kit (K903-1) - Includes a heavy gage
steel, approved spark arrestor, clamp and adapter for
mounting to the muffler exhaust pipe.
K953-1 TRAILER - Two-wheeled trailer with optional fender
and light package. For highway use, consult applicable feder-
al, state, and local laws regarding possible additional require-
ments. There is a choice of 2 hitches, a fender & a light pack-
age.
K953-1 Trailer
K958-1 Ball Hitch
K958-2 Lunette Eye Hitch
K959-1 Fender & Light Kit
K965-1 Cable Rack
OIL DRAIN KIT K1586-1 - Includes ball valve, hose
and clamp.
STICK OPTIONS
K704 ACCESSORY SET - Includes 35 feet (10 m) of
electrode cable and 30 feet (9 m) of work cable, head-
shield, work clamp and electrode holder. Cable is
rated at 500 amps, 60% duty cycle.

ACCESSORIES

(Field Installed)
CLASSIC 300D
Remote Control Kit (K924-4) - Contains switch,
receptacle, remote control rheostat, and 100 ft
(30.5m) cable for adjusting the OCV at the welding
site.(For Codes below 10911.)
Remote Control Kit (K924-5) - Contains remote
control rheostat and 100 ft. (30.5 m) cable for adjust-
ing the OCV at the welding site. (For Codes 10911
and above.)
Remote Control Kit (K2464-1) - Contains remote
control rheostat (for adjusting the CC "STICK OVC),
remote control potentiometer (for adjusting the CV
"WIRE" OCV) and 100 ft. (30.5 m) cable.
TIG OPTIONS
TIG Module (K930-2) - Provides high frequency and
shielding gas control for AC and DC GTAW (TIG)
welding applications. Its compact case is designed for
easy carrying, complete with a handle. High frequen-
cy bypass is built in.The K938-1 Contactor Kit must
be field installed in the TIG Module when used with a
ZR-10. Additionally, the K936-3 control cable is
required if remote control is used. If remote control is
not used the K936-4 control cable is required.
PTA-26V TIG Torch K1783-9-Air cooled 200 amp-
torch equipped with valve for gas flow control. 25Ft.
length.
Magnum Parts Kit For PTA-26V TIG Torch KP509
Remote Control Cable (K936-4) - Control cable for
connecting the K930-2 TIG Module to a ZR-10 not
equipped with a K892-1 Remote Kit. 9-Socket to a
grounded 115 V plug and a 6 pin MS-connector.
(Contains circuits 31, 32, and ground)
Arc Start Switch K814
Contactor Kit K938-1
Control Cable Extension K937-45-Cable is 45Ft. in
length.
Water Valve Kit K844-1-For use with a water-cooled
TIG torch. Installs inside TIG Module.
C-1