Slant/Fin SENTINEL SE-70 Installation And Operating Instructions Manual page 9

Sentinel
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand, don't
try to repair it, call a qualified service technician. Force or attempt-
ed repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and any
gas control which has been under water.
Lighting Instructions
1. STOP! Read the safety information on this page.
2. Set the thermostat to lowest setting.
3. Turn off all electric power to the appliance.
4. Remove control access panel.
5. Push in gas control knob slightly and turn clockwise
to "OFF".
6. Wait five (5) minutes (longer for propane) to clear out any gas,
then smell for gas, including near the floor. If you then
smell gas, STOP! Follow "B" in the safety informa-
tion on this page. If you don't smell gas, go to
next step.
7. Remove the pilot access panel located below
and behind the gas control unit.
8. Find pilot—follow metal tube from gas control. The pilot is
between two burner tubes behind the burner access panel.
9. Turn knob on gas control counterclockwise
10. Push in red button all the way and hold in. Immediately
light the pilot with a match. Continue to hold the red button in for
about one (1) minute after the pilot is lit. Release knob and it will
Figure 6. Valve VR8200, VR8300, V8200 or V800
pop back up. Pilot should remain lit. If it goes out, repeat steps 5
through 10.
– If knob does not pop up when released, stop and immediately call
your service technician or gas supplier.
– If the pilot will not stay lit after several tries, turn the gas control
knob to "OFF" and call your service technician or gas supplier.
11.Replace pilot access panel.
12.Turn gas control knob counterclockwise
13.Replace control access panel.
14.Turn on all electric power to the appliance.
15.Set thermostat to desired settings.
To Turn Off Gas To Appliance
1. Set the thermostat to lowest setting.
2. Turn off all electric power to the appliance if service is to be per-
formed.
3. Remove control access panel.
4. Turn gas control knob clockwise
force.
5. Replace control access panel.
Figure 7.
2. Intermittent Pilot System (IID).
FOR BOILERS EQUIPPED WITH HONEYWELL GAS
VALVE VR8204 or VR8304 (see figures 8 and 9).
WARNING: If you do not follow these instructions exactly,
a fire or explosion may result causing property damage, per-
sonal injury or loss of life.
to "PILOT".
A. This appliance is equipped with an ignition device which automati-
cally lights the pilot. Do not try to light the pilot by hand.
B. BEFORE OPERATING smell all around the appliance area for gas.
Be sure to smell next to the floor because some gas is heavier than
air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; Do not use any phone in your
• Immediately call your gas supplier from a neighbor's phone. Fol-
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob. Never
use tools. If the knob will not push in or turn by hand, don't try to
repair it, call a qualified service technician. Force or attempted repair
may result in a fire or explosion.
D. Do not use this appliance if any part has been under-water. Immedi-
ately call a qualified service technician to inspect the appliance and
to replace any part of the control system and any gas control which
has been underwater.
1. STOP! Read the safety information above.
2. Set the thermostat to lowest setting.
3. Turn off all electric power to the appliance.
to "ON".
4. This appliance is equipped with an ignition device which
automatically lights the pilot. DO NOT try to light the pilot
by hand.
5. Remove control access panel.
6. Turn gas control knob clockwise
then continue to "OFF". DO NOT force.
7. Wait five (5) minutes (longer for propane) to clear out any
gas, then smell for gas, including near the floor. If you then
smell gas, STOP! Follow "B" in the safety information
above on this page. If you don't smell gas, go to next step.
8. Turn gas control knob counterclockwise
9. Replace control access panel.
to "OFF". DO NOT
10. Turn on all electric power to the appliance.
SAFETY INFORMATION
FOR YOUR SAFETY READ BEFORE LIGHTING
building.
low the gas supplier's instructions.
Operating Instructions
9
until knob stops
to "ON".