Saeco PHEDRA Manual page 38

English
3.3.
Beverage 1
...
3.3.
Beverage 1
Sequence 0C00
3 = dispenses product 3
4 = dispenses product 4
5 = dispenses product 5
C = brews coffee using instantly ground coffee
F = brews "fresh brew" coffee using pre-ground coffee
P = brews espresso coffee using pre-ground coffee
B = brews "fresh brew" coffee using instantly ground coffee
W = dispenses hot water
S = dispenses steam in the Cappuccinatore
Consequently, the combination of "3C00" or "30C0" or
"03C0" will always dispense product 3 and coffee beans.
The settings of products making up the beverage will be
requested according to the sequence.
3.3.
Beverage 1
H2O coffee 38
It allows setting the quantity of water to be dispensed for the
programmed coffee type (C, P, F, or B). The quantity can be
set from "1" to "999".
3.3.
Beverage 1
Steam Duration
Cappuccinatore.
3.3.
Beverage 1
Just water 101
be brewed can be adjusted from "1" to "999".
3.3.
Beverage 1
% InstProd 3: 50
10 and 100. The lower the value the smaller the powder
delivery rate.
3.3.
Beverage 1
% Pump 3: 50
20 and 100. The lower the value the smaller the water
delivery rate.
38
SEQUENCE
This is the order in which
the products making up the
beverage are brewed. The
possible choices are:
0 = does not dispense any product
1 = dispenses product 1
2 = dispenses product 2
C O F F E E W A T E R , P R E -
GROUND WATER, FRESH-
B R E W W A T E R , B E A N S
WATER
STEAM DURATION
It determines the activation
time (in tenths of seconds) for
dispensing steam through the
JUST WATER
Defines the amount of hot
water to be dispensed.
The amount of coffee that can
% INSTANT PRODUCT
It determines the instant powder
delivery rate.
The value can be set between
% PUMP
It determines the water delivery
rate.
The value can be set between
Important
If the sequence includes several instant products, the
sequence "INSTANT PRODUCT - WATER - DELAY - INSTANT
PRODUCTS - % OF INSTANT PRODUCT" will be shown
again.
If the setting relative to the instant product ("INSTANT
PRODUCT - WATER - % INSTANT PRODUCT" - % PUMP)
means that the powder dispensing lasts longer than the
water dispensing, the vending machine stops powder
dosing (to avoid insufficient rinsing of the mixer) and emits a
beep. Check the settings again to obtain correct dispensing
(powder dispensing must end a few instants before the water
dispensing is complete, to allow good rinsing of the mixer).
3.3.
Beverage 1
InstProd D.3:005
indicates that the motor of the instant product 3 will be
activated for 5 tenths of a second.
The quantity of instant product is adjustable from "1" to
"500" in steps of 1. Brewing of the instant product does
not occur when the parameter is set at "0000" (in this case
water is brewed).
3.3.
Beverage 1
H2O InstPr.3:022
Example: "3" indicates that water will be mixed with the
instant product 3. "022" indicates that 22 water units will be
brewed with the instant product. The reference unit is preset
by the manufacturer. The amount of water can be adjusted
from '"1" to "1500" in steps of 1.
3.3.
Beverage 1
Test beverage
By pressing ENTER the message "PRESS KEY" is displayed
and it is possible to choose the key to be pressed, relative
to the type of brewing test:
- 3 key = Full beverage;
- 7 key = Water only;
- 8 key = Powder only.
INSTANT PRODUCT DOSE
This defines the quantity of
instant product to be brewed.
Example: "005" quantity
H2O / INSTANT PRODUCT
It defines the amount of water
to be mixed with the instant
powder.
BEVERAGE TEST
Enables brewing tests to be
carried out on the beverage
just set.