Others 2/3 Screen - Panasonic AW-HE40HWP Operating Instructions Manual

Camera menu items
■

Others 2/3 screen

### Others 2/3 ###
Zoom Mode
Max Digital Zoom
Image Stabilizer
Tally
IR Control
IR ID
CAM/BAR
Return
Zoom Mode
[Opt.Zoom, i.Zoom, D.Zoom, D.Extender]
Configure the maximum zoom magnification.
Opt.Zoom: Use only the optical zoom. Up to 30x optical
zoom is possible.
i.Zoom:
Enable the i.Zoom function.
Enabling this function allows you to perform
electronic zoom while reducing drops in
picture quality.
Combining optical zoom and electronic
zoom, up to 40x zoom is possible.
D.Zoom: Enable the digital zoom function.
Picture quality degrades as zoom increases
with digital zoom.
D.Extender: Enable the digital extender function.
When this function is enabled, you can
perform optical zoom while maintaining a
fixed digital zoom magnification. Smooth
zooming operations will be possible at the
cost of slight degradation in the image
quality.
Max Digital Zoom [x2 to x16]
Set the maximum digital zoom magnification.
This is only enabled when Zoom Mode is set to "D.Zoom".
Image Stabilizer [Off, On]
Turn the digital image stabilization function off/on.
Notes
● The field of view will be narrower when the image
stabilization function is active.
● When "On" is selected, video will be delayed by
1 frame.
● When switching between "On" and "Off", the
image may go black and the audio may be muted
temporarily.
● Image stabilization cannot be performed while
Frame Mix is active.
● The effect of the image stabilization function is
reduced in low-light environments.
● The unit's image stabilizer function detects
movement from the image signal and performs
correction. Depending on the shooting conditions,
the function may not be able to differentiate between
movement of the subject and movement of the unit,
resulting in correction errors.
(continued)
D.Zoom
×16
Off
Enable
Enable
CAM1
Camera
Tally [Disable, Enable]
"Enable" or "Disable" is set here for the function which
turns on or turns off the tally lamp using the tally control
signal.
IR Control [Disable, Enable]
"Enable" or "Disable" is set here for operations conducted
from the wireless remote control.
The operations are enabled when the unit's power is
turned on from an external device other than a wireless
remote control, and they are disabled when the power is
turned on from a wireless remote control.
Notes
● At the point when this item's setting is changed, the
new setting is not reflected in operation.
It is reflected when the unit is set to standby mode
and its power is turned on.
● Follow one of the procedures below if the item's
setting is changed by mistake and the unit can no
longer be operated from a wireless remote control.
When menu operations can be performed using
another control device:
 First change the item using a control device
capable of performing menu operations, and
then turn off the unit's power and turn it back
on.
When menu operations cannot be performed
using other control devices:
1. Turn off the power of the units and devices that
are connected.
2. Disconnect the unit's AC adaptor cable and
LAN cable, and plug them back in.
3. Perform the operation for turning on the unit's
power from the wireless remote control.
4. After changing this item, turn off the unit's
power and turn it back on.
IR ID [CAM1, CAM2, CAM3, CAM4]
Configure the unit's remote control ID.
The settings for this item correspond to the [CAM1] to
[CAM4] buttons on the wireless remote control.
CAM/BAR [Camera, Colorbar]
Switch between color bar display and camera image
display on the monitor and the web setup screen.
Note
● When the color bar is displayed, a test tone (1 kHz)
is output according to the Audio setting in the
camera menu.
Return
Use this to return to the previous menu.
47