Managing Client Qos Acls; Ipv4 And Ipv6 Acls; Table 52 - Vap Qos Parameters - D-Link DWL-2600AP Administrator's Manual

Unified Access Point Administrator's Guide
Field
Client QoS Mode
Bandwidth Limit
Down
Bandwidth Limit Up
ACL Type Down
ACL Name Down
ACL Type Up
ACL Name Up
DiffServ Policy
Down
DiffServ Policy Up

Managing Client QoS ACLs

ACLs are a collection of permit and deny conditions, called rules, that provide security by blocking unauthorized
users and allowing authorized users to access specific resources. ACLs can block any unwarranted attempts to reach
network resources.
The UAP supports up to 50 IPv4, IPv6, and MAC ACLs.

IPv4 and IPv6 ACLs

IP ACLs classify traffic for Layers 3 and 4.
Each ACL is a set of up to 10 rules applied to traffic sent from a wireless client or to be received by a wireless client.
Each rule specifies whether the contents of a given field should be used to permit or deny access to the network.
Rules can be based on various criteria and may apply to one ore more fields within a packet, such as the source or
destination IP address, the source or destination L4 port, or the protocol carried in the packet.
January 2015
Description
Enable or disable QoS operation on the VAP selected in the VAP menu.
QoS must be enabled globally (from the Client QoS Global Admin Mode field) and on the
VAP (QoS Mode field) for the Client QoS settings to be applied to wireless clients.
Enter the maximum allowed transmission rate from the AP to the wireless client in bits per
second. The valid range is 0 – 429496000 bits/sec.
The value you enter must be a multiple of 8000 bits/sec, in other words, the value must be
n × 8000 bits/sec, where n = 0, 1, 2, 3... If you attempt to set the limit to a value that is not
a multiple of 8000 bits/sec, the configuration will be rejected. A value of 0 means that the
bandwidth maximum limit is not enforced in this direction.
Enter the maximum allowed client transmission rate to the AP in bits per second. The valid
range is 0 – 4294967295 bps.
The value you enter must be n × 8000 bits/sec, where n = 0, 1, 2, 3... If you attempt to set
the limit to a value that is not a multiple of 8000 bits/sec, the configuration will be rejected. A
value of 0 means that the bandwidth maximum limit is not enforced in this direction.
Select the type of ACL to apply to traffic in the outbound (down) direction, which can be one
of the following:
•) IPv4: The ACL examines IPv4 packets for matches to ACL rules
•) IPv6: The ACL examines IPv6 packets for matches to ACL rules
•) MAC: The ACL examines layer 2 frames for matches to ACL rules
Select the name of the ACL applied to traffic in the outbound (down) direction.
After switching the packet or frame to the outbound interface, the ACL's rules are checked
for a match. The packet or frame is transmitted if it is permitted, and discarded if it is denied.
Select the type of ACL to apply to traffic in the inbound (up) direction, which can be one of
the following:
•) IPv4: The ACL examines IPv4 packets for matches to ACL rules
•) IPv6: The ACL examines IPv6 packets for matches to ACL rules
•) MAC: The ACL examines layer 2 frames for matches to ACL rules
Select the name of the ACL applied to traffic entering the AP in the inbound (up) direction.
When a packet or frame is received by the AP, the ACL's rules are checked for a match. The
packet or frame is processed if it is permitted, and discarded if it is denied.
Select the name of the DiffServ policy applied to traffic from the AP in the outbound (down)
direction.
Select the name of the DiffServ policy applied to traffic sent to the AP in the inbound (up)
direction.

Table 52 - VAP QoS Parameters

Section 8 - Configuring Client Quality of Service (QoS)
Unified Access Point Administrator's Guide
Page 89