Electrolux EDW 1003 Service Manual page 34

6.14. Service function / readout of fault memory and single actuator selection:
General information
w Calling the service functions is executed in all designs
resp. key arrangements analogously.
w For that you always have to use keys S0, S1, S2 and S3
independent of their variant-depending program load.
w In the service function mode, the key S1 is ALWAYS
responsible for the function "readout of fault memory"
and "single actuator selection".
EDW 1003 / VGA
LD1 LD2 LD3
S1 S3
It is generally valid:
For calling all service functions you always have first to
actuate function keys S1 and S3 before switching
on the appliance by ON/OFF switch S0!
The keys have to remain pressed aprox. 4 seconds
to activate the function.
This procedure is intentionally different to that for the
customer functions.
Calling above-mentioned service function
1. L D 1 LD2 LD3 L D 4
S1 S2 S3 S4
2 .
S1 S3
3.
S1 S3
ENDE
a l l e b l i n k e n
L D 1 LD2 LD3
S0
4.
S1 S3
L E D b l i n k t
L D 1
5.
S1
L E D b l i n k t
L D 1
S1
L E D b l i n k t
L D 2
S1
L D 1 L E D b l i n k t
6.
S1
LD1 L D 2 L D 3 LD4 LD5
. . . A U S n a c h 6 0 s e k . a u t o m a t i s c h
. . . A U S d u r c h m a n u e l l e B e t ä t i g u n g ü b e r E i n /A u s
Calling the functions
L D 5 L D 6
L D 7 L D 1 0
L D 8 L D 1 1
"readout of fault memory" and "single actuator selection"
L D 9 L D 1 2
S5 S6
S0
1.
2.
3. / 4. ... and switch on the appliance by ON/OFF switch S0.
S0
S0
5. / 6. By actuating the function key S1 you now can call the function.
3 - 4 S e k u n d e n
S0
Anzeige 2. + 3.Fehlers
pro Tastendruck
1 Weiterschaltung
S1
Anzeige
der Einzelaktoren
LD6
S0
S0
34
Appliance in switched-off condition
Press keys S1 and S3 simultaneously and
For that keep pressed keys S1 and S3 until the 3 confirmation
LEDs LD1, LD2 and LD3 are flashing.
(A temporary flashing up of LEDs is possible and is no fault!)
The confirmation LED LD1 continues flashing, the LEDs
LD2 and LD3 go out.
By pressing key S1 the first time the 1. fault is displayed
in a coded way via the "END" LED.
By pressing key S1 a second and third time it is possible to
read out the second and third value of the fault memory.
(see description page B 19 / "Survey of fault displays")
From pressing the key S1 the fourth time onward the LED
LD1 goes out and LD2 starts flashing.
Now you can call the single actuators one after the other.
4. Actuation: Selection of regeneration valve
5. Actuation: Selection of drain pump
6. Actuation: Selection of valve
(filling to level - if level already existing, no filling)
7. Actuation: Selection of heating
(only when level detected)
8. Actuation: Selection of circulation pump
9. Actuation: Selection of detergent dispenser
10.Actuation: Selection of drying fan
All positions can be called scrolling as many times as one wants.
The single steps are switched onward manually by pressing
a key. If the function key S1 is not pressed within 60 seconds,
the service function is left automatically. All LEDs of program
and option keys are lit. The appliance is in the "prestart" mode
again. It is also possible to leave the function by switching off
the appliance by ON/OFF key S0.