Table of Contents
Advertisement
ELECTROLUX HOME PRODUCTS
Customer Care - EMEA
Training and Operations Support
Technical Support
Edition: 05/2017 - Rev. 1.0
Publication number
599 79 76 - 53
EN
599 79 76 - 53 REV 1.0
SERVICE MANUAL
DISHWASHERS
Service Mode & ALARM
CODES
• EDW 503
• EDW 1953
• EDW 1103
• EDW 4013
• EDW 1503
• EDW 4033
• EDW 1753
Dishwashers with electronic
control system
Advertisement
Table of Contents
Related Manuals for Electrolux EDW 503
Summary of Contents for Electrolux EDW 503
- Page 1 SERVICE MODE & ALARM Customer Care - EMEA CODES Training and Operations Support Technical Support 599 79 76 - 53 • EDW 503 • EDW 1953 • EDW 1103 • EDW 4013 • EDW 1503 • EDW 4033 • EDW 1753 Edition: 05/2017 - Rev.
- Page 2 Introduction & Purpose Chapter 1 only by qualified Service Engineers. User Interface – Introduction Chapter 2 Always remove the plug from the EDW 503 Chapter 3.1 power socket before touching internal components. EDW 1103 Chapter 3.2 EDW 1503 Chapter 3.3 EDW 1753 Chapter 3.3...
- Page 3 User interface – Introduction According to hardware configuration of the dishwasher and User Interface – Modes and Function description marketing requirement, User Mode in individual models can be a Reset subset of above functions. “Reset” is a special kind of User Operation to stop or deselect a The User Mode functions are not described in this Service Manual running program.
- Page 4 User interface – Introduction Service Mode – Function description Alarm Reading and Actuator Test After accessed Service mode to get the saved alarms and test actuators. Details of alarm code displaying are in later Alarm Code section. LED Test / Delete Alarm Memory To test the LEDS and erase alarm codes from memory.
- Page 5 EDW503 EDW503 Reset Press the S1 which is dedicated to this function. Styling Overview Location of LEDs and Push Buttons Indication LEDs Access Service Mode 1. Reset 2. Turn off the dishwasher 3. Press and hold S1 while switching on the dishwasher. Keep holding the Program button until: ...
- Page 6 EDW503 Number of Alarm Reading and Actuator Test Actuator Comment S1 Pressed Regeneration Valve 1. After Service mode is accessed (when L1 is blinking, L2 and L3 Drain Pump is on), wait a few seconds till LED L2 and L3 to be turned off, Inlet Valve Off when water level reached then press the S1.
- Page 7 EDW503 Functional Test Cycle 1. After Service mode is accessed (when L1 is blinking, L2 and L3 is on), press S1 twice before L2 and L3 is turned off LED L3 is blinking, L1 and L2 is turned on 2.
- Page 8 EDW1503 / EDW1753 EDW1503 / EDW1753 Reset Models with “Cancel” key combination Styling Overview Open the dishwasher door, press buttons S2+S3 simultaneously for at least 2 seconds to perform Reset function. Location of Rotary, LEDs and Push Buttons Models with single “Reset” key Open the dishwasher door, press the specific button dedicated to this function for at least 2 seconds to perform Reset function.
- Page 9 EDW1503 / EDW1753 Access Service Mode 2. Press button S1 again to show the second alarm code. 3. Press button S1 once more to show the third alarm code. The Service Mode can only be accessed after the Reset function has been carried out and the appliance is switched off.
- Page 10 EDW1503 / EDW1753 LED Test / Delete Alarm Memory After accessed Service mode (L1, L2 and L3 blinking): Enable/disable Extra Rinse 1. Press button S2 to start this function. After accessed Service mode (L1, L2 and L3 blinking): All used LEDS and display (show “8:88”) blinks 5 second on 1.
- Page 11 EDW1103 Reset EDW1103 Models with “Cancel” key combination Open the dishwasher door, press buttons S2+S3 simultaneously for at least 2 seconds to perform Reset function. Styling Overview Models with single “Reset” key Location of LEDs and Push Buttons Open the dishwasher door, press the specific button dedicated to this function for at least 2 seconds to perform Reset function.
- Page 12 EDW1103 Access Service Mode 2. Press button S1 again to show the second alarm code. 3. Press button S1 once more to show the third alarm code. The Service Mode can only be accessed after the Reset function has been carried out and the appliance is switched off. 4.
- Page 13 EDW1103 LED Test / Delete Alarm Memory Enable/disable Extra Rinse After accessed Service mode (L1, L2 and L3 blinking): After accessed Service mode (L1, L2 and L3 blinking): 1. Press button S2 to start this function. 1. Press button S1+S2 to enter this function. ...
- Page 14 EDW1953 Reset EDW1953 Models with “Cancel” key combination Open the dishwasher door, press buttons S2+S3 simultaneously for at least 2 seconds to perform Reset function. Styling Overview Models with single “Reset” key Location of LEDs and Push Buttons Open the dishwasher door, press the specific button dedicated to this function for at least 2 seconds to perform Reset function.
- Page 15 EDW1953 Access Service Mode 2. Press button S1 again to show the second alarm code. 3. Press button S1 once more to show the third alarm code. The Service Mode can only be accessed after the Reset function has been carried out and the appliance is switched off. 4.
- Page 16 EDW1953 LED Test / Delete Alarm Memory Enable/disable Extra Rinse After accessed Service mode (L1, L2 and L3 blinking): After accessed Service mode (L1, L2 and L3 blinking): 1. Press button S2 to start this function. All used LEDS and display (show “8:88”) blinks 5 second on 1 second off.
- Page 17 EDW1953 Enable/disable Pulse Wash After accessed Service mode (L1, L2 and L3 blinking): 1. Press button S2+S3 to enter this function. L2 blinks indicating it is in Pulse Wash setting mode. Display show the current setting of Pulse Wash. “0P” for disabled, “1P”...
- Page 18 EDW 4013 / EDW4033 For EDW4033, press the Program Key for at least 2 seconds, and EDW 4013 / 4033 then follow the instructions on the screen to perform Reset function. Styling Overview The difference between User Interfaces can be detected by the buttons: EDW4013 - Horizontal menu structure (with Left and Right arrow keys) EDW4033 - Vertical menu structure (with Up and Down arrow keys)
- Page 19 EDW 4013 / EDW4033 After accessing Service mode, using the navigation buttons to select the desired service function shown in screen and using “OK” button to enter the selected function, then follow the instruction in the screen to perform the functions. Follow the instruction in the screen or switching off the appliance to save the new setting and exit Service mode.
- Page 20 Alarm Codes Alarm Code Description Alarm management • i00 Code family: Low mains voltage The electronic board makes sure the dishwasher operates within certain Alarm codes are defined in families of alarms and current voltage limits. If during a cycle the voltage drops below the lowest limit, the alarms, displayed as electronic board suspends all loads and interrupts the cycle under way.
- Page 21 Alarm Codes • i40 Codes - family : Analogue pressure sensor code: during dynamic filling problem • Acoustic signal and visual alarm, depending on the appliance customization; the program can be restarted. • The water level defined is not reached within the time limit set. •...
- Page 22 Alarm Codes • i46 • i55 code: Calibration invalid, pressure signal too high code: DCLink undervoltage • The warning is set if the sensor signal is out of range for an empty dw, • Alarm is set when the Vbat voltage on motorcontrolboard will be detected signal high.
- Page 23 Alarm Codes • i59 • i5B (i5H) code: WP current read ADC - fault code: WP/DP current plausibility • • Alarm is set if there is detected a fault in the current reading chain on MCB; Alarm is set if currents are not changing within 2.5 s with less than 0.0275 incl.
- Page 24 Alarm Codes • i60 Code - family : Heating Element Problem • i70 Code - family : Thermistor problem • i60 • i70 code: heating code: NTC sensor value out of range • The alarm is stored and displayed only in service mode; the washing •...
- Page 25 Alarm Codes • i82 • i95 code: Water Reuse valve warning code: UIDATA checksum mismatch • This warning is set if the Water Reuse valve is detected not opened during • The alarm is signalled if the UIDATA checksum type provided in the water tank conditioning, or configuration file mismatches with the attached UI board.
- Page 26 Alarm Codes Current production specific iB4 (iH4) • code: turbidity sensor too noisy calibration error • The alarm is set if the turbidity readings are too noisy during This range includes the following PBs and PB firmware releases: calibration, could be because of dirt or air bubbles disturbing the PB100 after P100R230 (including P100R230) turbidity sensor during calibration.
- Page 27 Alarm Codes • iD0 Code - family : Tacho Problem iF0 Code - family : water level problem • • iD0 • iF0 code: no signal Code : overfilling detected • The alarm is stored and displayed only in service mode; there is a new •...
- Page 28 Alarm Codes Service Code Reason Type User visible User failure Action in case of failure happens Dishwashers before Family indication code read March 2017 (Platform specific) User indication Zero cross or low voltage stop Nothing User interface off & remaining time adaptation off Nothing Fill_D –...
- Page 29 Alarm Codes Service Code Reason Type User visible User failure Action in case of failure happens Dishwashers before Family indication code read March 2017 (Platform specific) User indication WP BLDC motor not connected abort Cycle will be terminated and electronic switched to reset on-condition WP BLDC ADC fault abort Cycle will be terminated and electronic switched to reset on-condition...
- Page 30 Alarm Codes Service Code Reason Type User visible User failure Action in case of failure happens Dishwashers before Family indication code read March 2017 (Platform specific) User indication Please OBSERVE that iBx family has different meaning depending on PBs and PB firmware versions B0(DIVA2, PB100 Turbidity sensor problem warning...