Table of Contents
Advertisement
UNIT SIZE
ALTITUDE (FT)
(BTUH)
40,000
60,000
80,000
9001 to 10,000‡
(2743 to 3048)
100,000
120,000
* Disk usage-Unless otherwise specified, use perforated disk assembly (factory-supplied in loose parts bag).
# If one disk is stated, separate 2 halves of perforated disk assembly and use shouldered disk half. When using shouldered disk half, install screen side toward inlet box.
† Wide radius elbow.
‡ Vent sizing for Canadian installations over 4500 ft (1370 M) above sea level are subject to acceptance by the local authorities having jurisdiction. NA-Not Allowed;
pressure switch will not make.
NOTES:
1. Do not use pipe size greater than those specified in table or incomplete combustion, flame disturbance, or flame sense lockout may occur.
2. Size both the combustion-air and vent pipe independently, then use the larger diameter for both pipes.
3. Assume two 45° elbows equal one 90° elbow. Wide radius elbows are desirable and may be required in some cases.
4. Elbows and pipe sections within the furnace casing and at the vent termination should not be included in vent length or elbow count.
5. The minimum pipe length is 5 ft (1.5 M) for all applications.
6. Use 3-in. (76 mm) diameter vent termination kit for installations requiring 4-in (102 mm) diameter pipe.
FURNACE
NOT IN
HORIZONTAL
SECTION
Fig. 39 - - Combustion- -Air and Vent Pipe Diameter
Transition Location and Elbow Configuration
Table 11—Maximum Allowable Pipe Length --- Ft (M) (Continued)
DIRECT VENT (2-PIPE) ONLY
TERMINATION
PIPE DIA
TYPE
IN. (mm)*
2 Pipe or 2-in
1-1/2 (38)
Concentric
2 (51)
2 Pipe or 2-in
2 (51)
Concentric
2 (51)
2 Pipe or 2-in
Concentric
2-1/2 (64)
2-1/2 (64)
2 Pipe or 3-in
Concentric
3 (76)
NA
2 Pipe or 3-in.
Concentric
4 (102)† no
disk
PIPE DIAMETER
TRANSITION IN
VERTICAL SECTION
A93034
NON-DIRECT
VENT (1-PIPE)
ONLY
PIPE DIA
1
IN. (mm)*
42
1-1/2 (38)
(12.8)
57
2 (51)
(17.4)
45
2 (51)
(13.7)
30
2 (51)
(9.1)
57
2-1/2 (64)
(17.4)
21
2-1/2 (64)
(6.4)
54
3 (76)
(16.5)
39
3 (76)†
(11.9)
10
4 (102)† no disk
(3.0)
3/8 ID TUBE
3/16
DRILL
4"MIN
(102 mm)
TRAP
TO OPEN
DRAIN
Fig. 40 - - Air Intake Housing Plug Fitting Drain
- - 42 - -
NUMBER OF 90° ELBOWS
2
3
4
5
37
32
27
25
(11.3)
(9.8)
(8.2)
(7.6)
55
53
51
49
(16.8)
(16.2)
(15.5)
(14.9)
40
38
33
31
(12.2)
(11.6)
(10.1)
(9.4)
25
14
9
7
(7.6)
(4.3)
(2.7)
(2.1)
55
53
51
49
(16.8)
(16.2)
(15.5)
(14.9)
13
5
NA
NA
(4.0)
(1.5)
49
44
39
34
(14.9)
(13.4)
(11.9)
(10.4)
37
35
33
31
(11.3)
(10.7)
(10.1)
(9.4)
5
NA
NA
NA
(1.5)
COMBUSTION – AIR
INTAKE HOUSING
BURNER
BOX
COMBUSTION-AIR
PIPE (DIRECT
VENT/2 PIPE)
COMBUSTION-AIR
PIPE (NON-DIRECT
VENT/1-PIPE)
6
20
(6.1)
47
(14.3)
29
(8.8)
NA
47
(14.3)
NA
29
(8.8)
29
(8.8)
NA
A05093
Advertisement
Table of Contents
