Vertex Standard VX-1210 Service Manual page 26

Alignment
TX Gain Alignment 1 (SSB Hi Power)
r Connect the 50 W Dummy Load and Inline Wattmeter to the
ANT jack, then connect the AF Generator to the MIC IN jack
on the MIC Adapter Unit, and adjust the AF Generator to
1500 Hz, 8 mV.
r Referring Table below, turn the transceiver to each channel
listed, and recall the computer to each parameter listed by
pressing the [F7] key. Press the [F10] key to activate the
SPOT-ADJ mode, then key the transmitter and press the
[S ] + [p]/[q] keys for the required output.
HIFT
r Press the [F2] key to save the alignment value to the trans-
ceiver.
Tune to
"TXG S 1H" channel
( 3.50000 MHz, USB )
"TXG S 2H" channel
( 5.00000 MHz, USB )
"TXG S 3H" channel
( 7.50000 MHz, USB )
"TXG S 4H" channel
( 11.00000 MHz, USB )
"TXG S 5H" channel
( 16.50000 MHz, USB )
"TXG S 6H" channel
( 25.00000 MHz, USB )
TX Gain Alignment 2 (SSB Low Power)
r Connect the 50 W Dummy Load and Inline Wattmeter to the
ANT jack, then connect the AF Generator to the MIC IN jack
on the MIC Adapter Unit, and adjust the AF Generator to
1500 Hz, 8 mV.
r Referring Table below, turn the transceiver to each channel
listed, and recall the computer to each parameter listed by
pressing the [F7] key. Press the [F10] key to activate the
SPOT-ADJ mode, then key the transmitter and enter the align-
ment values using the numeric keys for the required output.
r Press the [F2] key to save the alignment value to the trans-
ceiver.
Tune to
"TXG S 1L" channel
( 3.50000 MHz, USB )
"TXG S 2L" channel
( 5.00000 MHz, USB )
"TXG S 3L" channel
( 7.50000 MHz, USB )
"TXG S 4L" channel
( 11.00000 MHz, USB )
"TXG S 5L" channel
( 16.50000 MHz, USB )
"TXG S 6L" channel
( 25.00000 MHz, USB )
26
Recall Parameter For
SSB Tx Ga Hi ( 00-04 )
20 W
SSB Tx Ga Hi ( 04-06 )
20 W
SSB Tx Ga Hi ( 06-09 )
20 W
SSB Tx Ga Hi ( 09-13 )
20 W
SSB Tx Ga Hi ( 13-20 )
20 W
SSB Tx Ga Hi ( 20-30 )
20 W
Recall Parameter For
SSB Tx Ga Lo ( 00-04 )
5 W
SSB Tx Ga Lo ( 04-06 )
5 W
SSB Tx Ga Lo ( 06-09 )
5 W
SSB Tx Ga Lo ( 09-13 )
5 W
SSB Tx Ga Lo ( 13-20 )
5 W
SSB Tx Ga Lo ( 20-30 )
5 W
TX Gain Alignment 1 (AM Hi Power)
r Connect the 50 W Dummy Load and Inline Wattmeter to the
ANT jack.
r Referring Table below, turn the transceiver to each channel
listed, and recall the computer to each parameter listed by
pressing the [F7] key. Press the [F10] key to activate the
SPOT-ADJ mode, then key the transmitter with no micro-
phone input and press the [S
required output.
r Press the [F2] key to save the alignment value to the trans-
ceiver.
Tune to
"TXG A 1H" channel
( 3.50000 MHz, AM )
"TXG A 2H" channel
( 5.00000 MHz, AM )
"TXG A 3H" channel
( 7.50000 MHz, AM )
"TXG A 4H" channel
( 11.00000 MHz, AM )
"TXG A 5H" channel
( 16.50000 MHz, AM )
"TXG S 6H" channel
( 25.00000 MHz, AM )
TX Gain Alignment 2 (AM Lo Power)
r Connect the 50 W Dummy Load and Inline Wattmeter to the
ANT jack.
r Referring Table below, turn the transceiver to each channel
listed, and recall the computer to each parameter listed by
pressing the [F7] key. Press the [F10] key to activate the
SPOT-ADJ mode, then key the transmitter with no micro-
phone input and press the [S
required output.
r Press the [F2] key to save the alignment value to the trans-
ceiver.
Tune to
"TXG A 1L" channel
( 3.50000 MHz, AM )
"TXG A 2L" channel
( 5.00000 MHz, AM )
"TXG A 3L" channel
( 7.50000 MHz, AM )
"TXG A 4L" channel
( 11.00000 MHz, AM )
"TXG A 5L" channel
( 16.50000 MHz, AM )
"TXG S 6L" channel
( 25.00000 MHz, AM )
] + [p]/[q] keys for the
HIFT
Recall Parameter For
AM Tx Ga Hi ( 00-04 )
20 W
AM Tx Ga Hi ( 04-06 )
20 W
AM Tx Ga Hi ( 06-09 )
20 W
AM Tx Ga Hi ( 09-13 )
20 W
AM Tx Ga Hi ( 13-20 )
20 W
AM Tx Ga Hi ( 20-30 )
20 W
] + [p]/[q] keys for the
HIFT
Recall Parameter For
AM Tx Ga Lo ( 00-04 )
5 W
AM Tx Ga Lo ( 04-06 )
5 W
AM Tx Ga Lo ( 06-09 )
5 W
AM Tx Ga Lo ( 09-13 )
5 W
AM Tx Ga Lo ( 13-20 )
5 W
AM Tx Ga Lo ( 20-30 )
5 W