Configurable Zone Types Worksheets - Honeywell ADEMCO VISTA-10P Programming Manual

CONFIGURABLE ZONE TYPES WORKSHEETS

Configurable zone type 90 can be programmed via downloader software or from a keypad using data fields*182-
*183.
Programming Configurable Zone Type options involves making 10 entries in data field *182, where each entry
represents the sum of the values of the various options shown in the tables below. Use field *183 to program a
Contact ID report code for this zone type.
ENTRY 1
(See note 4 for RF zones)
Response when system disarmed and zone is:
Intact EOL Open
RF zone normal RF zone N/A
0 = normal 0 = normal
1 = alarm 4 = alarm
2 = trouble 8 = trouble
3 = fault 12 = fault
Entry 1 = EOL + Open
ENTRY 3
(See note 4 for RF zones)
Response when armed STAY and zone is:
Intact EOL Open
RF zone normal RF zone N/A
0 = normal 0 = normal
1 = alarm 4 = alarm
2 = trouble 8 = trouble
3 = fault 12 = fault
Entry 3 = EOL + Open
ENTRY 5
(See note 4 for RF zones)
Response when armed AWAY and zone is:
Intact EOL Open
RF zone normal RF zone N/A
0 = normal 0 = normal
1 = alarm 4 = alarm
2 = trouble 8 = trouble
3 = fault 12 = fault
Entry 5 = EOL + Open
ENTRY 7
Display Faults Power Reset/
Verification
0 = show alarms 0 = no
when armed 4 = power reset
& disarmed after fault
1 = don't show (by code + OFF)
12 = verification
alarms when
(see zone
armed
(show
type 16)
alarms, trbles,
faults when
disarmed)
3 = never show
any alarms,
trbles, faults
Entry 7 = fault display + power
reset/verification
ENTRY 9
Alarm Sounds Use Bell
Timeout
0 = none 0 = no
1 = steady 4 = yes
keypad
2 = steady bell see fields *32,
and keypad *33
3 = pulsing bell
and keypad
Entry 9 = alarm sounds + bell timeout + fire zone
ENTRY 2
(See note 4 for RF zones)
Auto
Restore
Shorted
RF zn off-normal
0 = normal 0 = no
1 = alarm 4 = yes
2 = trouble
3 = fault
Entry 2 = Short + auto restore + vent zone
ENTRY 4
(See note 4 for RF zones)
Byp. when
disarmed
Shorted
RF zn off-normal
0 = normal 0 = no
1 = alarm 4 = yes
2 = trouble
3 = fault
Entry 4 = Short + byp. disarmed + byp. armed
ENTRY 6
(See note 4 for RF zones)
Dial Delay
(see field *50)
Shorted
RF zn off-normal
0 = normal 0 = no
1 = alarm 4 = use delay
2 = trouble
3 = fault
Entry 6 = Short + dial delay + fault delay
ENTRY 8
Use Entry Use Exit
Delay 1/2 Delay
0 = no 0 = no
1 = delay 1 4 = use exit
2 = delay 2 delay
Entry 8 = entry delay 1/entry delay 2 + exit delay +
interior zone type
ENTRY 10
Respond as Trouble
Fire Zone Sounds
0 = no 0 = none
8 = yes 1 = periodic
beep
see zone type 2 = trouble
09; see note 4 beeps
Entry 10 = trouble sounds + chime
WWW.DIYALARMFORUM.COM
Entry
1
Vent Zone
2
0 = no
3
8 = yes
4
5
6
7
8
Byp. when 9
armed
10
To calculate the value for each entry:
0 = no
Simply add the values of the selected options
8 = yes
in each of the entry's columns (one option per
column). For example, to program Entry 2 for
"alarm response to short," "auto restore on,"
but not a "vent zone," enter 5 ("1" for alarm
short + "4" for auto restore yes + "0" for vent
zone no).
Fault Delay
(see field *87)
0 = no
8 = use delay
see note 1
Respond as
Interior Type
NOTES:
0 = no
1. Do not use the "fault delay" option with a
8 = yes
see note 2
2. To create an interior type zone, select
3. Do not set fire zones to respond as a
4. RF Zones: The "open" option in entries 1,
Chime when
Chime Mode On
0 = no
4 = yes
– 6 –
Entries for Fields *182
Zone Type 90 (field *182)
INTACT OPEN SHORTED
EOL
ZONE-003-V0
Zone Conditions Represented
in Entries 1-6
configurable zone type if it is set for an
entry or exit delay, otherwise
unpredictable results may occur.
"respond as interior zone type" (entry 8,
interior type = yes), and set zone
response to "fault" in entries 3-4 to ensure
fault displays; do not set as "normal,"
"alarm," or "trouble."
"fault" (entries 1-6), otherwise faults will
not display unless the [∗] key is pressed.
3, and 5 is not applicable for RF zones.
Use the "intact EOL" option for normal RF
zone conditions and "shorted" for off-
normal RF zone conditions.