Configurable Zone Types Worksheets - Honeywell Ademco VISTA-20PCN Programming Manual

Configurable Zone Types Worksheets

Configurable zone types 90 and 91 can be programmed via downloader software or from a keypad using data
fields*182-*185. Configurable zone types 92 and 93 (VISTA-20P only) can only be programmed using the
downloader software.
Programming Configurable Zone Type options involves entering 10 digits in data field *182 for zone type 90 and
field *184 for zone type 91, where each digit represents the sum of the values of its various options as shown in
the tables below. Use fields *183 and *185 to program Contact ID report codes for these zone types.
DIGIT 1
(See note 5 for RF zones)
Response when system disarmed and zone is:
Intact EOL Open
RF zone normal RF zone N/A
0 = normal 0 = normal
1 = alarm 4 = alarm
2 = trouble 8 = trouble
3 = fault 12 = fault
Digit 1 = EOL + Open
DIGIT 3
(See note 5 for RF zones)
Response when armed STAY and zone is:
Intact EOL Open
RF zone normal RF zone N/A
0 = normal 0 = normal
1 = alarm 4 = alarm
2 = trouble 8 = trouble
3 = fault 12 = fault
Digit 3 = EOL + Open
DIGIT 5
(See note 5 for RF zones)
Response when armed AWAY and zone is:
Intact EOL Open
RF zone normal RF zone N/A
0 = normal 0 = normal
1 = alarm 4 = alarm
2 = trouble 8 = trouble
3 = fault 12 = fault
Digit 5 = EOL + Open
DIGIT 7
Display Faults Power Reset/
Verification
0 = show alarms 0 = no
when armed 4 = power reset
& disarmed after fault
(by code + OFF)
1 = don't show
12 = verification
alarms when
(see zone
armed
(show
type 16)
alarms, trbles,
faults when
disarmed)
3 = never show
any alarms,
trbles, faults
Digit 7 = fault display + power
reset/verification
DIGIT 9
Alarm Sounds Use Bell
Timeout
0 = none 0 = no
1 = steady 4 = yes
keypad
2 = steady bell see fields *32,
and keypad *33
3 = pulsing bell
and keypad
Digit 9 = alarm sounds + bell timeout + fire zone
DIGIT 2
(See note 5 for RF zones)
Auto
Restore
Shorted
RF zn off-normal
0 = normal 0 = no
1 = alarm 4 = yes
2 = trouble
3 = fault
Digit 2 = Short + auto restore + vent zone
DIGIT 4
(See note 5 for RF zones)
Byp. when
disarmed
Shorted
RF zn off-normal
0 = normal 0 = no
1 = alarm 4 = yes
2 = trouble
3 = fault
Digit 4 = Short + byp. disarmed + byp. armed
DIGIT 6
(See note 5 for RF zones)
Dial Delay
(see field *50)
Shorted
RF zn off-normal
0 = normal 0 = no
1 = alarm 4 = use delay
2 = trouble
3 = fault
Digit 6 = Short + dial delay + fault delay
DIGIT 8
Use Entry Use Exit
Delay 1/2 Delay
0 = no 0 = no
1 = delay 1 4 = use exit
2 = delay 2 delay
Digit 8 = entry delay 1/entry delay 2 + exit delay +
interior zone type
DIGIT 10
Respond as Trouble
Fire Zone Sounds
0 = no 0 = none
8 = yes 1 = periodic
beep
see zone type 2 = trouble
09; see note 4 beeps
Digit 10 = trouble sounds + chime
Digit
Vent Zone
1
2
0 = no
8 = yes
3
4
5
6
7
8
Byp. when
9
armed
10
0 = no
To calculate each digit's entry:
8 = yes
Simply add the values of the selected options
in each of the digit's columns (one option per
column). For example, to program Digit 2 for
"alarm response to short," "auto restore on,"
but not a "vent zone," enter 5 ("1" for alarm
short + "4" for auto restore yes + "0" for vent
Fault Delay
zone no).
(see field *87)
0 = no
8 = use delay
see note 1
NOTES:
Respond as
1. Do not use the "fault delay" option with a
Interior Type
0 = no
8 = yes
see note 2 2. To create an interior type zone, select
3. Do not set fire zones to respond as a
4. 4219/4229 modules must use EOLRs or
5. RF Zones: The "open" option in digits 1,
Chime when
Chime Mode On
0 = no
4 = yes
6. Zone-Doubling/Double-Balanced: A short
– 8 –
Entries for Fields *182 and *184
Zone Type 90 Zone Type 91
(field *182) (field *184)
INTACT OPEN SHORTED
EOL
-018-V0
Zone Conditions Represented
in Digits 1-6
configurable zone type if it is set for an
entry or exit delay, otherwise
unpredictable results may occur.
"respond as interior zone type" (Digit 8,
interior type = yes), and set zone
response to "fault" in digits 3-4 to ensure
fault displays; do not set as "normal,"
"alarm," or "trouble."
"fault" (digits 1-6), otherwise faults will not
display unless the [∗] key is pressed.
unpredictable results may occur.
3, and 5 is not applicable for RF zones.
Use the "intact EOL" option for normal RF
zone conditions and "shorted" for off-
normal RF zone conditions.
on either zone of a zone-doubled pair or
on a double-balanced zone causes a
tamper condition.