Setting Switchblade's Midi Channel And Switching Omni On/Off - Hughes & Kettner SwitchBlade Head 100 Manual

Switchblade
6.1.3 TAP
The function gives you a very fast and convenient option for
TAP
changing the Delay's TIME
on stage: Simply tap your foot on the
groove to match delay Time to the tempo. The effect adopts the new
time after the second tap. The
in time with the beat to give you a visual indication of the delay time.
Note: The TAP function works only when the DELAY is active. If the
DELAY is off, the effect will not adopt your TAP tempo.
6.1.4 Switching External Devices via the
FSM 432, Setting the MIDI Send Channel
If you wish to switch devices connected to
– say, a MIDI effect device – using the FSM 432, ensure the effect
device is set to the FSM 432's MIDI Channel or to
device's manual for more info.
To set the FSM 432's MIDI Send Channel, proceed as follows:
• Turn
on while pressing the FSM 432's
SWITCHBLADE
button. The display flashes.
• Release button A. Use
to a number between 1 and 16.
• Quit and store by pressing the
Caution: If SWITCHBLADE and FSM 432 are not set to the same
MIDI channel, the amp will not respond to program changes!
Activating OMNI solves the problem in the event of an "emergency."
See chapter 6.2 to learn more.
Note: If an external effect device is connected to MIDI THRU and
you want to switch Switchblade and the effect device simultaneously
with the same program change command, you must configure
Switchblade's Store function and program this device accordingly.
Note: The table above should be big help if you wish to switch the
Presets of a device connected to the MIDI THRU directly via the
FSM 432. It shows the program changes sent by the bank/preset
combination. Please bear in mind that some MIDI devices switch
program 1 via program change command 0. If this is the case with
your outboard gear, simply add a 1 to each value indicated in this
table to activate the desired program.
20
parameter. TAP comes in particularly handy
TAP button in Time with the
TAP LED flashes for about five seconds
SWITCHBLADE MIDI THRU
OMNI
to view and set the MIDI Channel
UP/DOWN
button.
PRESET A
1 A
1 B
1 C
1 D
2 A
2 B
2 C
2 D
3 A
3 B
3 C
. Consult the
3 D
4 A
4 B
4 C
PRESET A
4 D
5 A
5 B
5 C
5 D
6 A
6 B
6 C
6 D
7 A
7 B
7 C
7 D
8 A
8 B
8 C
8 D
6.2 Setting Switchblade's MIDI
Channel and Switching OMNI ON/OFF
Press the SERIAL
is in normal operating mode, and the
flashing. This assigns special programming functions to the amp's LEDs
and buttons:
FX ON
Now serves as a +1/
Serial
Now serves as a -1/
Store
OMNI ON/OFF
SWITCHBLADE
of the MIDI Channel over which they are sent. If the light on the button
is extinguished (
defined MIDI Channel.
0 9 A 32 17 A
1 9 B 33 17 B
2 9 C 34 17 C
3 9 D 35 17 D
4 10 A 36 18 A
5 10 B 37 18 B
6 10 C 38 18 C
7 10 D 39 18 D
8 11 A 40 19 A
9 11 B 41 19 B
10 11 C 42 19 C
11 11 D 43 19 D
12 12 A 44 20 A
13 12 B 45 20 B
14 12 C 46 20 C
15 12 D 47 20 D
16 13 A 48 21 A
17 13 B 49 21 B
18 13 C 50 21 C
19 13 D 51 21 D
20 14 A 52 22 A
21 14 B 53 22 B
22 14 C 54 22 C
23 14 D 55 22 D
24 15 A 56 23 A
25 15 B 57 23 B
26 15 C 58 23 C
27 15 D 59 23 D
28 16 A 60 24 A
29 16 B 61 24 B
30 16 C 62 24 C
31 16 D 63 24 D
button longer than two seconds when
ORIGINAL VALUE
UP button for setting the MIDI Channel.
DOWN button for setting the MIDI Channel.
switches. If the STORE button (OMNI On) lights up,
responds to all incoming program changes, irrespective
), it responds only to messages sent via the
OMNI OFF
64 25 A 96
65 25 B 97
66 25 C 98
67 25 D 99
68 26 A 100
69 26 B 101
70 26 C 102
71 26 D 103
72 27 A 104
73 27 B 105
74 27 C 106
75 27 D 107
76 28 A 108
77 28 B 109
78 28 C 110
79 28 D 111
80 29 A 112
81 29 B 113
82 29 C 114
83 29 D 115
84 30 A 116
85 30 B 117
86 30 C 118
87 30 D 119
88 31 A 120
89 31 B 121
90 31 C 122
91 31 D 123
92 32 A 124
93 32 B 125
94 32 C 126
95 32 D 127
SWITCHBLADE
LED will start