Phono Operation; Bluetooth Operation - Jensen JMC-1250 User Manual

Note :
If no buttons are pressed after 5 seconds when setting the Radio Station Presets,
the JMC-1250 will return to tuner mode
The Radio Station Presets may be lost if the main power switch is turned off. If
this occurs, you will need to reset the Radio Station Preset.
You can overwrite a present station by saving the new frequency in its place.
FM and FM Stereo Reception
1. Release the FM Mode button (#6) to select Stereo Mode. The LCD display (#2)
will show "ST" when receiving a stereo program.
2. Press down FM Mode button (#6) to select Mono Mode. The LCD display (#2)
will not show "ST" even receiving a stereo program.
Note : It is preferable to receive the program in Mono Mode when you are receiving
a weak station.
TIPS FOR BEST RECEPTION
AM - The AM antenna is located inside the cabinet of the main unit. If AM reception
is weak, change the position of cabinet until the internal antenna picks up the
strongest signal,
FM - During FM reception, always keep the FM Wire Antenna (#38) fully extended.
If FM reception is weak try repositioning the FM Wire Antenna until you find
the strongest signal.

PHONO OPERATION

Noted :
- Remove the stylus protector.
- Be sure that the tone arm is being detached from
the tone arm rest before operating and re-secured
again afterwards.
1. Press the PHONO/BLUETOOTH/AUX BUTTON (#24) repeatedly to select
Phono Mode. The LCD DISPLAY (#2) will show PHONO.
2. Set the Speed selector (#33) to the proper position depending on the record to
be played.
3. Place the record on the platter; use the SPINDLE ADAPTOR (#32) when
playing 45 RPM records.
4. Lift the tone arm from the rest and slowly move it to
the record side. The platter will start to rotate.
5. Place the tone arm to the desired position of the
record.
6. Adjust the volume to the desired level.
7. At the end of record, the platter will automatically stop
rotating. Lift the tone arm from the record and return it
to the rest.
8. To stop manually, lift the tone arm from the record and return it to the rest.
Remark :
The auto-stop may not work on some records because the play area is out of the
preset adjustment, so it may stop before the last track finishes. When this happens
disable the the auto-stop feature by placing the auto-stop switch (#34) in the " off
" position, then it will run to the end of the record but will not stop automatically
(turn off the unit by power button or switch back the auto-stop switch (#34) to
"on" position to stop the platter rotate). Then put back the tone arm to the rest
position.

BLUETOOTH OPERATION

Pairing a Bluetooth enabled device with the JMC-1250.
1. Press the POWER ON/STANDBY BUTTON (#7) to turn on the JMC-1250.
2. Press the PHONO/BLUETOOTH/AUX BUTTON (#24) repeatedly to select
Bluetooth Mode. The LCD DISPLAY (#2) will show BT.
3. The BLUETOOTH INDICATOR (#18) will flash.
Pairing/Discoverable mode.
4. Turn on the Bluetooth function for the device you want to link to, and enable the
search or scan function to find the JMC-1250.
5. Select "JMC-1250" from the device list when it appears on your device screen.
If required, enter the pass code "0000" to pair (link) JMC-1250 with your device.
6. If you are pairing (linking) your computer to the speaker using Bluetooth, you
may need to set the JMC-1250 as your computer's default sound device.
7. After successfully pairing the JMC-1250 with your Bluetooth device, The
BLUETOOTH INDICATOR (#18) will stop flashing and remain lit.
8. If you want to pair (link) the JMC-1250 with another Bluetooth device, press and
hold Play/Pause button (#22) a few
(#18) will flash. The JMC-1250 will go into Pairing/Discoverable mode. Repeat
steps 4 & 5.
Now you can play music from your Bluetooth device wirelessly to the JMC-1250.
1. Select your favorite song, press the
Play/Pause Button (#22) on the
your Bluetooth device.
2. Press the Skip Forward Button (#12) or Skip Backward
select the Next or Previous track.
(The SEARCH function does not apply to Bluetooth operation )
3. Slowly adjust both the volume controls of your JMC-1250 and your Bluetooth
device until you reach a comfortable listening level.
Note :
1. Refer to the manual of your cell phone, tablet PC, computer or other Bluetooth
enabled devices for Bluetooth operation since it may vary from model to
model.
2. If your Bluetooth enabled device does not support A2DP profile, it will not play
the music through the speaker, even if paired (linked).
3. Remember to turn off the JMC-1250 when you have finished listening,
E-10
The JMC-1250 will go into
seconds. The BLUETOOTH INDICATOR
Play/Pause on your Bluetooth device or
JMC-1250 to play or pause the song from
Button (#9) to
E-11
the