Panasonic WV-SW396 Installation Manual page 10

Do not damage the power cable.
Do not damage, fabricate, twist, stretch, bundle, or forci-
bly bend the power cable. Do not place heavy objects.
Keep away from heat sources.
Use of the damaged power cable may cause electric
shock, short circuit, or fire.
Consult the dealer for repair.
Do not install this product on a place that is greatly
influenced by wind.
Installation on a place where the wind speed is 40 m
{131.23 feet} or more per second may cause a fall of the
product resulting in injury or accidents.
Turn the power off when cleaning this product.
Failure to observe this may cause injury.
[Precautions for use]
This product has no power switch.
When turning off the power, disconnect the power supply
from the 24 V AC power supply or the PoE+ device. When
using both the 24 V AC power supply and the PoE+ device
for power supply, disconnect both the connections.
To keep on using with stable performance
Do not use this product in hot and humid conditions for a
long time. Failure to observe this causes component deg-
radation resulting in life shortening of this product.
Do not expose this product to direct heat sources such as
a heater.
Do not touch the dome cover with your bare hands.
A dirty dome cover causes deterioration of picture quality.
Handle this product with care.
Do not drop this product, nor apply shock or vibration to
the product. Failure to observe this may cause trouble.
Do not give a strong shock to the dome cover.
It may cause damage or water exposure.
About the PC monitor
When displaying the same image on the PC monitor for a
long time, the PC monitor may be damaged.
It is recommended to use a screen-saver.
When an error is detected, this product will restart
automatically.
This product will be inoperable for around 2 minutes after
the restart just as when the power is turned on.
Product disposal/transfer
Data saved on this product or a storage device used with
this product may lead to personal information leakage.
When it is necessary to dispose or give this product to
someone, even when for repair, make sure that there is no
data on this product.
10
Cleaning this product body
Be sure to turn off the power before cleaning. Failure to
observe this may cause injury. Do not use strong abrasive
detergent when cleaning this product. Otherwise, it may cause
discoloration. When using a chemical cloth for cleaning, read
the caution provided with the chemical cloth product.
Important:
• The camera position may be moved inadvertently while
cleaning the camera body. Restart the product or
refresh the camera position (position refresh) to correct
the camera position. Refer to the Operating Instructions
(included in the CD-ROM) for further information.
Transmission interval
Image transmission interval may become slow depending
on the network environment, PC performance, shooting
subject, access number, etc.
When the following message appears on the screen
during use
CAUTION:
POWER SUPPLY IS ONLY
INTENDED FOR USE OF
POE+(CLASS4) HUB
-IEEE802.3AT COMPLY
OR
AC24V MIN3.0A CLASS2
SUPPLY
The product may not be connected to a proper power-
supply device. Check whether the power supply device in
use is compatible with PoE+ (IEEE802.3at compliant). Or
use 24 V AC power supply.
What to do if "WARMING UP-PLEASE WAIT"
appears on the display.
This message indicates that the temperature inside the
camera has become extremely low.
In such a case, wait until the heater unit of the camera
raises the internal temperature (for around 2 hours or more
in low temperatures below –10 ºC {14 ºF}), and turn on
the power again.
About SDHC/SD memory card
• Before inserting the SDHC/SD memory card, turn off
the power of this product first. Otherwise, it may
cause malfunction or damage data recorded on the
SDHC/SD memory card.
Refer to page 15 for descriptions of how to insert/
remove an SDHC/SD memory card.
• When using an unformatted SDHC/SD memory card,
format it using this product. Recorded data on the
SDHC/SD memory card will be deleted when format-
ted. If an unformatted SDHC/SD memory card or an
SDHC/SD memory card formatted with other devices
is used, this product may not work properly or perfor-
mance deterioration may be caused. Refer to the
Operating Instructions (included in the CD-ROM) for
how to format a SDHC/SD memory card.