Floating Display Assembly Replacement; Top Light Replacement; Heater Assembly Replacement - Dimplex PF2325 Service Manual

8. Follow the wiring to the main control board and replace
with new connection.
9. Properly orient and insert the new LED light assembly.
10. Reassemble in the reverse order as above.
FLOATING DISPLAY ASSEMBLY
REPLACEMENT
Tools Required: Phillips Head Screwdriver
CAUTION: If unit was operating prior to servicing allow
at least 10 minutes for heating elements and top panel to
cool off to avoid accidental burning of skin.
WARNING: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or damage
to persons.
1. Unplug the unit from power outlet.
2. Remove the firebox from the front of the mantel and
remove front glass assembly (glass lifts off).
CAUTION: Even though the glass is safety glass it
may break if bumped, struck of dropped. Care must be
taken when handling the glass.
3. Remove the loose media from the unit (if applicable).
4. Remove the 14 screws around the back panel of the
firebox and the 3 along the middle of the panel (Figure
3).
5. Locate the floating display assembly. (Figure 4)
6. Remove the 2 screws located at the top of the assem-
bly, gently remove the board and surrounding bracket.
7. Follow the wiring to the main control board and replace
with new connection.
8. Properly orient and insert the new floating display as-
sembly.
9. Reassemble in the reverse order as above.

TOP LIGHT REPLACEMENT

Tools Required: Phillips Head Screwdriver
Needle Nose Pliers
CAUTION: If unit was operating prior to servicing allow
at least 10 minutes for heating elements and top panel to
cool off to avoid accidental burning of skin.
WARNING: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or damage
to persons.
1. Unplug the unit from power outlet.
2. Remove the firebox from the front of the mantel and
remove front glass assembly (glass lifts off).
CAUTION: Even though the glass is safety glass it
may break if bumped, struck of dropped. Care must be
taken when handling the glass.
3. Remove the loose media from the unit (if applicable).
4. Remove the 14 screws around the back panel of the
firebox and the 3 along the middle of the panel (Figure
3).
10
5. Locate the top light that requires to be replaced. (Fig-
ure 4)
6. Release door that houses the LED light board by press-
ing the tab to the left and opening the door.
7. Release the LED light board from the top panel by us-
ing needle nose pliers to depress the tab on the mount-
ing standoffs and gently lift the board off.
8. Follow the wiring to the main control board and replace
with new connection.
9. Properly orient and insert the new board.
10. Reassemble in the reverse order as above.

HEATER ASSEMBLY REPLACEMENT

Tools Required: Phillips Head Screwdriver
CAUTION: If unit was operating prior to servicing allow
at least 10 minutes for heating elements and top panel to
cool off to avoid accidental burning of skin.
WARNING: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or damage
to persons.
1. Unplug the unit from power outlet.
2. Remove the firebox from the front of the mantel and
remove front glass assembly (glass lifts off).
CAUTION: Even though the glass is safety glass it
may break if bumped, struck of dropped. Care must be
taken when handling the glass.
3. Remove the loose media from the unit (if applicable).
4. Remove the 14 screws around the back panel of the
firebox and the 3 along the middle of the panel (Figure
3).
5. Locate the heater assembly and disconnect the wiring
connections noting their original locations.
!
NOTE: A flat head screwdriver can be used to gently
pry between the end of the connector and the switch to
release the wires.
6. Remove the 4 screws that secure the heater assembly
to the unit (2 on the top and 2 on the bottom). (Figure
6)
7. Properly orient and install the new heater assembly
and connect all of the wiring.
WARNING: Ensure wires do not come in contact with
moving parts by securing wires in wiring tie wraps.
8. Reassemble in the reverse order as above.
Top Mounting Screws
Figure 6
Bottom Mounting Screws
www.dimplex.com