Floating Display Assembly / Main Control Board Replacement; Top Light Replacement - Dimplex PF2325 Service Manual

3. Remove the loose media from the unit (if applicable).
4. Remove the 14 screws around the back panel of the
firebox and the 3 along the middle of the panel (Figure
3).
5. Locate the flame LED light assembly, at the bottom of
the unit. (Figure 4)
6. Locate and remove the two screws on either end secur-
ing the bracket, that the light assembly and the flicker
rod are attached to, and remove assembly (Figure 5).
7. Using the small adjustable wrench remove the 3 nuts to
remove the LED light assembly.
8. Follow the wiring to the main control board and replace
with new connection.
9. Properly orient and insert the new LED light assembly.
10. Reassemble in the reverse order as above.
FLOATING DISPLAY ASSEMBLY / MAIN
CONTROL BOARD REPLACEMENT
Tools Required: Phillips Head Screwdriver
CAUTION: If unit was operating prior to servicing allow
at least 10 minutes for heating elements and top panel to
cool off to avoid accidental burning of skin.
WARNING: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or damage
to persons.
MOD 0-A
1. Unplug the unit from power outlet.
2. Remove the firebox from the front of the mantel and
remove front glass assembly (glass lifts off).
CAUTION: Even though the glass is safety glass it
may break if bumped, struck of dropped. Care must be
taken when handling the glass.
3. Remove the loose media from the unit (if applicable).
4. Remove the 14 screws around the back panel of the
firebox and the 3 along the middle of the panel (Figure
3).
5. Locate the floating display assembly. (Figure 4)
6. Remove the 2 screws located at the top of the assem-
bly, gently remove the board and surrounding bracket.
7. Follow the wiring to the main control board and replace
with new connection.
Figure 5
Mounting Screws
Securing Nuts
Flame LED Light
8. Properly orient and insert the new floating display as-
9. Reassemble in the reverse order as above.
MOD B
1. Unplug the unit from power outlet.
2. Remove the firebox from the front of the mantel and
may break if bumped, struck of dropped. Care must be
taken when handling the glass.
3. Remove the loose media from the unit (if applicable).
4. Remove the 14 screws around the back panel of the
5. Locate the floating display assembly. (Figure 4)
6. Transfer the connections from the existing board to the
7. Remove the 4 screws securing the board to the assem-
8. Properly orient and insert the new floating display as-
9. Reassemble in the reverse order as above.

TOP LIGHT REPLACEMENT

Tools Required: Phillips Head Screwdriver
at least 10 minutes for heating elements and top panel to
cool off to avoid accidental burning of skin.
maintenance to reduce the risk of electric shock or damage
to persons.
1. Unplug the unit from power outlet.
2. Remove the firebox from the front of the mantel and
may break if bumped, struck of dropped. Care must be
taken when handling the glass.
3. Remove the loose media from the unit (if applicable).
4. Remove the 14 screws around the back panel of the
5. Locate the top light that requires to be replaced. (Fig-
Media LED Light
sembly.
remove front glass assembly (glass lifts off).
CAUTION: Even though the glass is safety glass it
firebox and one in the middle of the panel (Figure 3).
new display/control board.
bly.
sembly.
Needle Nose Pliers
CAUTION: If unit was operating prior to servicing allow
WARNING: Disconnect power before attempting any
remove front glass assembly (glass lifts off).
CAUTION: Even though the glass is safety glass it
firebox and the 3 along the middle of the panel (Figure
3).
Top Mounting Screws
Figure 6
Bottom Mounting Screws
13