JR 10X User Manual page 40

2. Touch the lower left SEL to activate the gyro sensitivity system
and to obtain the following display:
Indicates AUX2 is selected
Indicates function being
programmed
Touch to select
AUX2 switch or Flight Touch
between standard gyro
Modes to activate gyro
gain and Stick Priority
gains in flight
for aileron/elevator or
rudder gyro gain
Indicates AUX2 switch is
being used to select
positions for programming
3. Touch SEL at the top of the display until AUX2 is displayed
and highlighted as shown. This indicates that the display is
ready to accept gyro gain values for the gyro plugged into the
AUX2 channel (see display above).
4. Touch SEL at the lower left of the screen until AUX2 appears
under the highlighted AUX2. This indicates that the AUX2
switch will be used (at least for now) to select which gain posi-
tion is to be programmed (see display above).
5. Now touch SEL under CENT to activate Stick Priority Gyro
Gain and the display will appear as illustrated below. Touch
SEL again until the appropriate channel (AILE, ELEV,
RUDD) appears.
Indicates AUX2 is selected
Touch
between AUX2 and
Indicates function being
AUX3 to set gains
programmed
Touch to
Touch to
select Aux2 Switch
toggle between top
or Flight Modes to and bottom
activate gyro gains percentages for
in flight
center stick and full
end stick deflection
Touch
Indicates AUX2 switch is
increase or decrease
being used to select
gyro gain settings for
positions for programming each position for center
stick and full stick
deflection
A new row of gain percentages appears. The top row next to
CENT indicates the gyro gain percentages that are in effect for
AUX2 when the stick is centered. The bottom row indicates the
gyro gain for AUX2 when the stick is fully deflected in either
direction. In addition, END RUDD appears to indicated that the
rudder stick is selected to control stick priority for the AUX2
channel.
40
Touch to toggle
between AUX2 and Touch
to exit function
AUX3 to set gains
to toggle Touch or to
increase or decrease
gyro gain settings
Indicates gyro gain
settings for each
position (0, 1, 2)
to toggle
Touch to
save programming
and exit function
Touch to select stick/channel
to be used for stick priority (rudder,
elevator, or aileron)
Indicates gyro gain settings for
each position (0, 1, 2) for center
or to
stick and full stick deflection
In this example, notice that the first position (Position 0) is set to
have a gain of 0% for both the CENT and END RUDD so that the
gyro gain can be turned off completely. The second position
(Position 1) CENT gain is set to 30% and its END RUDD is set
to 0%. This will cause the gyro gain to be 30% when the stick is
centered and will cause the gain to progressively decrease to 0 as
the stick is fully deflected. The third position (Position 2) has
been set to 70% for CENT and 0% for END RUDD — it has full
gain when the stick is centered and no gain when the stick is fully
deflected.
Note: The END percentages are typically set to 0% to provide
complete stick priority/override at full stick deflection.
Setting the Gain Percentages
6. Touch SEL under CENT until the proper control stick is dis-
played (rudder, elevator or aileron). It is the stick that corre-
sponds to the control that is to be controlled by the gyro
plugged into AUX2.
7. Use the AUX2 switch to select each of the three gyro gain
positions (0, 1, 2). When the AUX2 switch is in the upper
position, an arrow appears to the left of the first gyro gain
position (Position 0) as indicated in the display above. Now
touch SEL under END to select between the CENT percent-
age and end point percentage (END RUDD) and touch the +
and - keys to set the percentage of each.
Note: It's a good idea to leave the first position equal to 0% for
both gyros as it will provide the ability to turn the gyro gain com-
pletely off in the event that the gyro becomes over-sensitive.
8. Put the AUX2 switch in the middle position (Position 1) and
note that the arrow moves to the middle gain position on the
display. Now touch SEL and END to select between the
CENT percentage and end point percentage (END RUDD)
and touch the + or - keys to set the percentage of each (use
this position to set a moderate the amount of gain). Finally,
move the AUX2 switch to the lower position and set the gain
for the third position (Position 2). Use this last setting for the
highest gain you intend to use without causing an over-sensi-
tive condition in the gyro(s).
9. If a second gyro is used, touch SEL at the top of the screen to
select the AUX3 gyro gain, and touch SEL under CENT to
select the stick that corresponds with the control that is to be
controlled by the AUX3 gyro. Now repeat the process above
to set the CENT and end point gains for this gyro.
10. If you're going to use the AUX2 switch to select gyro gains in
flight, touch ENTER to save the programming and exit the
function. If you're going to assign gyro gains to Flight Modes,
touch the lower left SEL until FM appears and then touch
PAGE. Refer to the section on the preceeding page on
Assigning Gyro Gains to AUX2 or Flight Modes.
Note: The stick priority mixing is a linear mix and the gain is
reduced/increased in direct proportion to stick position.
10X MANUAL Airplane