Getting Started - Burnside TX2 User Manual

Getting started

Remove the clip-on lid to expose the SIM holder and insert a standard size SIM card.
Connect the battery and replace the lid. Connect the antenna, telephone and landline where
appropriate. See the supplied quick start guide for illustrations.
Connect the supplied charger. When charge power is connected for the first time after connecting
the battery, the battery circuit will be conditioned which will take a few seconds. The charge LED will
flash to indicate when the terminal has entered normal charge mode. See the section on LEDs.
The terminal will now be in "charge only mode" and will not be connected to the mobile network. If
the terminal is a TX2LR model, the landline will be connected through to the phone connection.
Turn on the terminal by pressing and holding the red button on the rear of the terminal, when the left
two LEDS light, release the button and the terminal will operate. It will take a few seconds to register
with the mobile network. Now the terminal is ready to make or receive calls.
To test the connection of the connected phone, try a ringback test by dialling *9# and hang up. The
phone should ring.
To test the landline on the TX2L/TX2LR, with the handset off-hook, press the recall button on the
phone and the landline will be connected.
LEDs
There are three LEDs on the terminal. The right hand green LED indicates the state of charging
which applies whether the terminal is in "charge only" mode or when it is operating.
The middle green LED indicates the mode of operation. The left orange LED indicates if the terminal
requires attention.
The table below shows the state and timings of the 3 LEDs. The solid graphic block character ■
represents the LED on, the □ represents the LED off. The ratios illustrated are approximate.
Left
[← 2 seconds
□□□□□□□□□□□□□□□□□□□□
□□□□□□□□□□□□□□□□□□□□
□□□□□□□□□□□□□□□□□□□□
□□□□□□□□□□□□□□□□□□□□
□□□□□□□□□□□□□□□□□□□□
■■■■■■■■■■■■■■■■■■■■
■□□□□□□□□□■□□□□□□□□□
□□□□□□□□□□□□□□□□□□□□
■■■■■□□□□□■■■■■□□□□□
■■■■■□□□□□■■■■■□□□□□
■□□□□□□□□□□□□□□□□□□□
□□□□□□□□□□□□□□□□□□□□
□□□□□□□□□□□□□□□□□□□□
□□□□□□□□□□□□□□□□□□□□
□□□□□□□□□□□□□□□□□□□□
■■■■■■■■■■■■■■■■■■■■
The xxxxxxx states of the charging LED during normal terminal operation can be any of the normal
charging states.
Middle
→] [← 2 seconds
□□□□□□□□□□□□□□□□□□□□
□□□□□□□□□□□□□□□□□□□□
□□□□□□□□□□□□□□□□□□□□
□□□□□□□□□□□□□□□□□□□□
□□□□□□□□□□□□□□□□□□□□
■■■■■■■■■■■■■■■■■■■■
□□□□□□□□□□□□□□□□□□□□
■□□□□■□□□□■□□□□■□□□□
□□□□□□□□□□□□□□□□□□□□
■■■■■□□□□□■■■■■□□□□□
■□□□□□□□□□□□□□□□□□□□
■□□□□□□□□□□□□□□□□□□□
■■■■■□□□□□■■■■■□□□□□
■■■■■■■■■■■■■■■■■■■□
■■■■■■■■■■■■■■■■■■■■
□□□□□□□□□□□□□□□□□□□□
© 2014 Burnside Technology Ltd.
Right ← Position & colour
→] [←2 s→] Function/Mode
□□□□□□ Inactive
■□□□□□ Conditioning power circuit
■■■■■□ Charge only mode charging
■■■■■■ Charge only mode charged
■■■□□□ Battery fault
xxxxxxx On/Off Button pressed
■□□□□□ Battery too low, please wait
xxxxxxx Starting/searching
xxxxxxx Waiting for PIN
xxxxxxx Waiting for PUK
xxxxxxx Weak signal (calls possible)
xxxxxxx Ready for call
xxxxxxx Incoming call
xxxxxxx Mobile call in progress
xxxxxxx PSTN Call in progress
xxxxxxx Fault such as no SIM
Page 4 of 24
Rev 1.1