Baofeng UV-82 User Manual page 72

Menu Number
/ Short Name
Memory Channel Programming
This menu is used to either create new or modify existing channels (0 through 127) so that
they can be accessed from MR/Channel Mode. The behavior of menu 27 changes
depending on whether the target channel is empty or has been previously programmed
(see below).
Note: Programming must be done in [A] VFO
Empty Target Channel:
The RX and TX frequencies of the target channel are set to the [A] VFO frequency. The
settings of the following menus are also saved into the target channel. This essentially
creates a fully operational simplex channel.
Menu 2 - TXP
Menu 5 - WN
Menu 10 - R-DCS
Menu 11 - R-CTCS
Menu 12 - T-DCS
Menu 13 - T-CTCS
27
MEM-CH
Menu 17 - S-CODE PTT-ID DTMF Code Selection
Menu 19 - PTT-ID
Menu 23 - BCL
Previously Programmed Target Channel:
The TX frequency of the target channel is set to the [A] VFO frequency. The settings of the
following menus are also saved into the target channel. Uses for this can be to update a
newly created 'simplex' channel into a 'repeater' channel or a 'cross-band' channel.
Another use would be to add, change or remove a TX DCS code or TX CTCSS tone.
Menu 12 - T-DCS
Menu 13 - T-CTCS
Note:
Note: TDR should be set to OFF when manually programming
Note:
Delete a Memory Channel
28
This menu is used to delete the programmed information from the specified channel (0
DEL-CH
through 127) so that it can either be programmed again or be left empty.
Back Light Color - Standby
29
WT-LED
Settings: OFF[0] | BLUE[1] | ORANGE[2] | PURPLE[3]
Back Light Color - Receive
30
RX-LED
Settings: OFF[0] | BLUE[1] | ORANGE[2] | PURPLE[3]
Back Light Color - Transmit
31
TX-LED
Settings: OFF[0] | BLUE[1] | ORANGE[2] | PURPLE[3]
Alarm Mode
Settings: SITE[0] | TONE[1] | CODE[2]
SITE: Sounds alarm through your radio speaker only
32
TONE: Transmits a cycling tone over-the-air
AL-MOD
CODE:
Note:
Reference for UV-82 Menus
by Jim Unroe - KC9HI
(send comments, suggestions or corrections to UV-82@KC9HI.net)
Long Name / Description / Settings / Notes
Transmit Power
Wideband / Narrowband
Digital Coded Squelch (DCS) - Receive/Decode
Continuous Tone Coded Squelch System (CTCSS) -
Receive/Decode
Digital Coded Squelch (DCS) - Transmit/Encode
Continuous Tone Coded Squelch System (CTCSS) -
Transmit/Encode
When to Send PTT-ID
Busy Channel Lockout
Digital Coded Squelch (DCS) - Transmit/Encode
Continuous Tone Coded Squelch System (CTCSS) -
Transmit/Encode
When the TX frequency differs from RX frequency, a '+-' is indicated
in the status display
It is a good idea to check the above menus prior to using menu 27 to
make sure none of them have an unwanted setting that was left over
from a previous programming session.
Transmits '119' (911 in reverse?) followed by the ANI code over-the-
air
Recommended setting is OFF... but since that isn't a choice use
SITE
11-January-2014
Default: PURPLE
Default: BLUE
Default: ORANGE
Default: TONE
Separate
MR/ VFO/
Channel Frequency
Global Mode Mode
✓
✓
✓
✓
✓
✓
Stored
VFO on a Per
A & B Channel
Settings Basis