Table of Contents
Advertisement
Menu Number
/ Short Name
Keypad Beep
8
Allows audible confirmation of a key press
BEEP
Settings: OFF[0] | ON[1]
Transmission Timer (seconds)
This feature provides a safety switch which limits transmission time to a programmed
value. This will promote battery conservation by not allowing you to make excessively-long
transmissions, and in the event of a stuck PTT switch (perhaps if the radio or a
Speaker/Mic is wedged between car seats) it can prevent interference to other users as
9
well as battery depletion.
TOT
Settings:
Note: (TIMEOUT-15)/15=[n]
Note:
Digital Coded Squelch (DCS) - Receive/Decode
Mutes the speaker of the transceiver in the absence of a specific low level digital signal. If
the station you are listening to does not transmit this specific signal, you will not hear
anything.
10
Settings: OFF[0] | see DCS Table
R-DCS
Note:
Note: Setting R-DCS sets menu 11 to OFF
Note: Recommended setting is OFF
Continuous Tone Coded Squelch System (CTCSS) - Receive/Decode
Mutes the speaker of the transceiver in the absence of a specific and continuous sub-
audible signal. If the station you are listening to does not transmit this specific and
continuous signal, you will not hear anything.
Settings: OFF[0] | see CTCSS Table
Note:
11
R-CTCS
Note:
Note:
Note: R-CTCS works properly (selectively) while not scanning
Note: Setting R-CTCS sets menu 10 to OFF
Note: Recommended setting is OFF
Digital Coded Squelch (DCS) - Transmit/Encode
Transmits a specific low level digital signal to unlock the squelch of a distant receiver
(usually a repeater).
12
Settings: OFF[0] | see DCS Table
T-DCS
Note: Setting T-DCS sets menu 13 to OFF
Note:
Continuous Tone Coded Squelch System (CTCSS) - Transmit/Encode
Transmits a specific and continuous sub-audible signal to unlock the squelch of a distant
receiver (usually a repeater).
13
Settings: OFF[0] | see CTCSS Table
T-CTCS
Note: Setting T-CTCS sets menu 12 to OFF
Note:
Reference for UV-82 Menus
by Jim Unroe - KC9HI
(send comments, suggestions or corrections to UV-82@KC9HI.net)
Long Name / Description / Settings / Notes
15[0] - 600[39] in 15 second steps (set TOT
Table)
The red TX LED begins to flash 10 seconds before the timeout limit
is reached
When R-DCS is not set to OFF, 'DCS' is indicated to the left of the
upper channel display
When R-CTCS is not set to OFF, 'CT' is indicated to the left of the
upper channel display
(R-CTCS ≤ 131.8 Hz) Scanning never stops regardless of the correct
CTCSS tone being received
(R-CTCS ≥ 141.3 Hz) Scanning stops regardless of the actual
CTCSS tone being received
When T-DCS is not set to OFF, 'DCS' is indicated to the left of the
upper channel display (requires TX or 'reverse' mode)
When T-CTCS is not set to OFF, 'CT' is indicated to the left of the
upper channel display (requires TX or 'reverse' mode)
11-January-2014
Default: ON
Default: 60
Default: OFF
Default: OFF
Default: OFF
Default: OFF
Separate
MR/
VFO/
Channel
Frequency
Global
Mode
Mode
✓
✓
RO
✓
RO
✓
RO
✓
RO
✓
Stored
VFO
on a Per
A & B
Channel
Settings
Basis
✓
✓
✓
✓
✓
✓
✓
✓
Hide quick links:
Advertisement
Table of Contents
