Heat & Glo ST-HVBI-AU Installation And Operation Instructions Manual
  1. Manuals
  2. Brands
  3. Heat & Glo Manuals
  4. Gas Heater
  5. ST-HVBI-AU
  6. Installation and operation instructions manual
Heat & Glo ST-HVBI-AU Installation And Operation Instructions Manual

Heat & Glo ST-HVBI-AU Installation And Operation Instructions Manual

Hide thumbs Also See for ST-HVBI-AU:
Table of Contents

Advertisement

Quick Links

INSTALLATION AND OPERATION INSTRUCTIONS
This appliance has been retired.
Service parts pages within have been removed.
For replacement parts, please refer to the individual
service parts list located on the brand websites.
AUSTRALIAN GAS ASSOCIATION CERTIFIED
High temperatures may ignite clothing or other fl ammable materials.
• Keep clothing, furniture, draperies and other fl ammable materials away.
This appliance has been supplied with an integral barrier to prevent direct contact with the
fi xed glass panel. DO NOT operate the appliance with the barrier removed.
HEAT & GLO, a brand of Hearth & Home Technologies Inc.
7571 215
THIS PRODUCT MAY BE COVERED BY ONE OR MORE OF THE FOLLOWING PATENTS:
(United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495,
5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502,
6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652,
D445174, D462436; (Canada) 1297749, 2195264, 2225408; (Australia) 543790;586383; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.
MODEL: ST-HVBI-AU
CERTIFICATE NUMBER 6027
WARNING
HOT SURFACES!
Glass and other surfaces are hot during operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as fi replace.
• Alert children and adults to hazards of high temperatures.
THIS MANUAL MUST BE USED FOR INSTALLATION AND RETAINED
BY HOMEOWNER FOR OPERATION AND MAINTENANCE.
th
Street West, Lakeville, MN 55044, USA, www.heatnglo.com
Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10
1

Advertisement

Table of Contents
loading

Related Manuals for Heat & Glo ST-HVBI-AU

Summary of Contents for Heat & Glo ST-HVBI-AU

  • Page 1 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408; (Australia) 543790;586383; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending. Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 2 Save this manual for future reference. Heat & Glo, a brand of Hearth & Home Technologies, Inc. 7571 215 Street West, Lakeville, MN 55044 Copyright 2009 • Printed in U.S.A. Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

  • Page 3: Table Of Contents

    3.2 Removal of Components for Service ............31 3.3 Parts Replacement ..................31 3.4 Adjustments and Replacement Parts ............31 3.5 Troubleshooting ................... 32 4.0 REPLACEMENT PARTS................... 35 Limited Warranty ....................37 Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

  • Page 4: Installation Instructions

    36-3/16 in. (610m) (121mm) (114mm) (919.3mm) TOP STANDOFFS FLUE COLLAR FLUE COLLAR LOUVER ACCESS DOOR GAS CONTROLS & LABELS GAS LINE ELECTRICAL ACCESS ACCESS Figure 1. Diagram of the ST-HVBI-AU Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

  • Page 5: Locating The Heater

    Metal Sides or Ends ...13 ....1/2 Top ........64 ....2-1/2 Ceiling* ......787 ....31 * The clearance to the ceiling is measured from the top of the unit, excluding the standoffs (see Figures 1 and 2). Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

  • Page 6: Framing The Heater

    4 in.) lumber or heavier. 42-5/8 in. 42-1/2 in. 23 in. 35 in. 53-3/4 in. (1.21 m) (1.08 m) (584 mm) (889 mm) (1.37 m) Figure 3. Framing Dimensions Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 7 LP Gas cylinder. A fl ue terminal is considered to be a source of ignition. MINIMUM CLEARANCES REQUIRED FOR BALANCED FLUE TERMINALS OR THE FLUE TERMINALS OF OUTDOOR APPLIANCES Figure 4 Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 8 NOTE: PIPES OVERLAP 32 mm (1-1/4 in.) AT EACH JOINT. Figure 5. DVP-Series Direct Flue Component Specifi cations (127 mm (5 in.) inner pipe / 203 mm (8 in.) outer pipe) Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

  • Page 9: Flue System Approvals And Installations

    fl ueing confi guration used. STORM COLLAR VERTICAL TERMINATION ROOF FLASHING HORIZONTAL TERMINATION WALL FIRESTOPS PIPE LENGTH 90º ELBOW TERMINATION KITS CEILING FIRESTOP DVP-TRAP DVP-TVHW Figure 6. Flue System Components and Termination Kits Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 10 STRAIGHT UP VERTICAL FLUEING V (FT.) 12.2 M MAX. (40 ft.) TERMINATION CAP Figure 7 STRAIGHT OUT HORIZONTAL FLUEING Max. Run 610 mm (24 in.) Figure 8 Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 11 5’ MIN. (1.5 m) 10’ MAX. (3.0 m) V + H = 40’ MAX. (12.2 m) V + H = 40’ MAX. (12.2 m) Figure 10. Flueing with One 90° Elbow Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 12 8’ MAX. (2.4 m) 5’ MIN. (1.5 m) 10’ MAX. (3.0 m) V + V + H = 40’ MAX. (12.2 m) Figure 11. Flueing with Two 90° Elbows Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 13 V + H + H = 40’ MAX. (12.2 m) H + H = 15’ MAX. (4.5 m) H + H = 10’ MAX. (3.0 m) Figure 13. Flueing with Two 90° Elbows Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 14 + H + H = 36’ MAX. (10.9 m) H + H = 12’ MAX. (3.6 m) H + H = 8’ MAX. (2.4 m) Figure 14. Flueing with three 90° elbows Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 15 10’ MAX. (3.0 m) V+ V + H + H = 36’ MAX. (10.9 m) H + H = 10’ MAX. (3.0 m) Figure 15. Flueing with three 90° elbows Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 16 • Overlap pipe slip sections at least 1-1/2 inches (38 mm). • Use pilot holes for screws. • Screws must not exceed one inch long. • Pipe may separate if not properly joined. Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 17 For elbows that are changing the fl ue direction, two screws minimum should be put in the outer fl ue at the joint to prevent the elbow from rotating. Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 18 12" (305 mm) CHIMNEY HOLE Figure 22. 254 mm x 305 mm Hole and Flue Pipe EXISTING CEILING JOISTS FRAMING MEMBERS CEILING Figure 24. Hole & New Framing Members Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 19 Figure 27. Flueing through the Wall RAFTER • The termination kit should pass through the wall fi restops from the exterior of the building. CEILING CEILING FIRESTOP Figure 26. Attic Firestop Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 20 WARNING: FOLLOWING NATIONAL REG- Figure 29. Minimum Height from Roof to ULATIONS AND CODES OF PRACTICE Lowest Discharge Opening FOR MINIMUM CLEARANCES FROM GAS TERMINALS, AND PLACEMENT OF GAS TERMINAL. Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

  • Page 21: Connecting The Gas Supply

    IGNITION MODULE (6V) 6VDC GROUND NEUTRAL BATTERY PORT PLUG IN THERMOCOUPLE ON/OFF BLOCK SWITCH (CONNECTED TO BACK OF VALVE) VALVE GAS LINE CONNECTED TO BACK OF VALVE Figure 31 Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

  • Page 22: Blower Wiring

    Figure 32 shows the BLACK (HOT) BROWN fan, switches, and fan wiring diagram. Figure 33 BROWN shows the wire connection detail. BLUE (NEUTRAL) BLUE BLUE Figure 33. Wire Connection Detail Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

  • Page 23: Mantel Clearances

    1010 INSIDE EDGE OF DRESS GUARD OPENING DRESS GUARD NOTE: ALL DIMENSIONS ARE SHOWN IN MILLIMETERS Figure 34 HIGH TEMP (300º F. 150 C. MIN.) SEAL JOINT Figure 35 Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

  • Page 24: Log Placement

    LOG #2 (SRV2068-701): Locate log #2 in left front corner of the log grate using bottom grooves for placement. Push log against grate tabs on fi rst and second bars. Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 25 Place log #5 on top of fl at spot on log #1 and against the inside of log #2. Be careful not to reposition log #2 when placing this log. Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 26 LOG #6 (SRV582-705): Position log #6 on top of the groove in log #3 with the forked end resting on the grate assembly as shown. Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

  • Page 27: Installer Testing

    Natural Gas Propane Gas Inlet Pressure 1.13 kPa 2.75 kPa Outlet Pressure .70 kPa 2.36 kPa Max. Gas Consumption 44.0 mJ/h 34.0 mJ/h Burner Injector 3.26 mm 1.70 mm Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

  • Page 28: Operation Cautions

    fi re or injury from burns and no part of it should be and the button to decrease the fl ame height. permanently removed. For protection of young children Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

  • Page 29: Safety And Lighting Information

    OFF (as shown in Figure 38) to shut off manually. The switch must be returned to the ON position prior to operation once power is restored. SWITCH IS SHOWN IN “ON” POSITION Figure 38 Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

  • Page 30: Fan Operation

    Clean all foreign materials from top of burner. Check to make sure that the burner orifi ce is clean. Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

  • Page 31: Removal Of Covers For Servicing

    Remove two pilot bracket retaining screws (see Figure 41.) Slide the burner away from the burner orifi ce. PILOT BRACKET RETAINING SCREWS Figure 41 CAUTION: ALL SCREWS WHICH WERE RE- MOVED MUST BE REPLACED. Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 32 4. Inspect for corrosion or separation. 5. Verify weather stripping, sealing and fl ashing remains intact. Remote controls 1. Verify operation of remote. 2. Replace batteries in remote transmitters and battery-powered receivers. Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

  • Page 33: Troubleshooting

    Ignitor gap is too large. Verify that spark gap from ignitor to pilot hood is .43 cm. c. Module is not grounded. Verify module is securely grounded to metal chassis of heater. Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 34 3. Be sure glass is tightened properly on unit, particularly on top corners. Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

  • Page 35: Replacement Parts

    Limited Lifetime Warranty Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...
  • Page 36 Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

  • Page 37: Limited Warranty

    Melbourne Jetmaster 444 Swan Street Richmond 3121 (03) 9429-5573 Perth Fireplace Corner 277 Lord Street East Perth 6000 (08) 9228-2600 Sydney Jetmaster 10 Martin Avenue Arncliff 2205 (02) 9597-7222 Heat & Glo • ST-HVBI-AU • 2082-900 Rev. J • 10/10...

Table of Contents