Page 2 Vigor2130 Series High Speed Gigabit Router User’s Guide Version: 2.0 Firmware Version: V1.5.1 Date: 28/07/2011 Vigor2130 Series User’s Guide...
Page 3 Web registration is preferred. You can register your Vigor router via Be a Registered http://www.draytek.com. Owner Due to the continuous evolution of DrayTek technology, all routers will be regularly Firmware & Tools upgraded. Please consult the DrayTek web site for more information on newest Updates firmware, tools and documents.
Page 4: Regulatory Information
Product: Vigor2130 Series Router DrayTek Corp. declares that Vigor2130 Series of routers are in compliance with the following essential requirements and other relevant provisions of R&TTE Directive 1999/5/EEC. The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive 2004/108/EC by complying with the requirements set forth in EN55022/Class B and EN55024/Class B.
Page 5: Table Of Contents
Case 2: VPN direction from Vigor2820 to Vigor2130 .............. 44 3.4 How to configure settings for DLNA Service in Vigor2130............ 47 3.5 How to download BT Torrent to USB Device via Vigor Router..........51 3.6 How to configure Dynamic DNS Service on Vigor2130............58 Vigor2130 Series User’s Guide...
Page 6 4.7.6 Wake On LAN....................... 136 4.8 VPN and Remote Access....................137 4.8.1 Remote Access Control ....................137 4.8.2 PPTP Remote Dial-in....................138 4.8.3 IPSec Remote Dial-in ....................141 4.8.4 Remote Dial-in Status....................142 4.8.5 LAN to LAN........................144 Vigor2130 Series User’s Guide...
Page 7 4.15.3 Routing Table ......................219 4.15.4 System Log......................... 220 4.15.5 Traffic Overview......................221 4.15.6 Detailed Statistics ....................... 222 4.15.7 MAC Address Table....................224 4.15.8 DHCP Table........................ 225 4.15.9 Data Flow Monitor....................... 226 4.15.10 Sessions Table ......................227 Vigor2130 Series User’s Guide...
Page 8 5.4 Checking If the ISP Settings are OK or Not ................ 233 5.5 Forcing Vigor Router into TFTP Mode for Performing the Firmware Upgrade ....234 5.6 Backing to Factory Default Setting If Necessary ..............237 5.7 Contacting Your Dealer ....................... 238 viii Vigor2130 Series User’s Guide...
Page 9: Preface
The Vigor2130 series are the routers with high speed in data transmission through WAN port and LAN ports. With hardware NAT acceleration, the rate of Vigor2130 series can be ideal for multi-media application. With the development of NGN (Next Generation Network), you may recently hear the news about FTTx deployment in your local area or even have already subscribed the unbundling last mile service (e.g.
Page 10: Led Indicators And Connectors
The DoS/DDoS function is active. Blinking It will blink while detecting an attack. Interfac Description Connector for accessing the Internet. Connectors for local networked devices. (1/2/3/4) Connector for USB storage device (Pen Driver/Mobile (1/2) HD) or printer or 3G backup. Vigor2130 Series User’s Guide...
Page 11 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Connector for a power adapter. Power Switch. ON/OFF Vigor2130 Series User’s Guide...
Page 12: For Vigor2130N
Press the button once to enable (WLAN LED on) or WLAN disable (WLAN LED off) wireless connection. Connector for accessing the Internet. Connectors for local networked devices. (1/2/3/4) USB (1/2) Connector for USB storage device (Pen Driver/Mobile HD) or printer or 3G backup. Vigor2130 Series User’s Guide...
Page 13 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Connector for a power adapter. Power Switch. ON/OFF Vigor2130 Series User’s Guide...
Page 14: For Vigor2130Vn
Press the button once to enable (WLAN LED on) or WLAN disable (WLAN LED off) wireless connection. Connector for accessing the Internet. Connectors for local networked devices. (1/2/3/4) USB (1/2) Connector for USB storage device (Pen Driver/Mobile HD) or printer or 3G backup. Vigor2130 Series User’s Guide...
Page 15 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Connector for a power adapter. Power Switch. ON/OFF Vigor2130 Series User’s Guide...
Page 16: Hardware Installation
4 PCs directly. Connect Phone port to a conventional analog telephone. Connect detachable antennas to the router for Vigor2130 series (n model). Connect one end of the power cord to the power port of this device. Connect the other end to the wall outlet of electricity.
Page 17: Stand Installation
The Vigor2130 must be placed erectly. Therefore you have to install a stand onto the router to make it standing firmly. Please follow the figures listed below to finish the installation. Vigor2130 Series User’s Guide...
Page 18: Printer Installation
You can install a printer onto the router for sharing printing. All the PCs connected this router can print documents via the router. The example provided here is made based on Windows XP/2000. For Windows 98/SE/Vista, please visit www.draytek.com. Before using it, please follow the steps below to configure settings for connected computers (or wireless clients).
Page 19 Click Local printer attached to this computer and click Next. In this dialog, choose Create a new port Type of port and use the drop down list to select Standard TCP/IP Port. Click Next. Vigor2130 Series User’s Guide...
Page 20 In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Printer Name or IP Address and type IP_192.168.1.1 as the port name. Then, click Next. Click Standard and choose Generic Network Card. Then, in the following dialog, click Finish. Vigor2130 Series User’s Guide...
Page 21 11. Select "LPR" on Protocol, type p1 (number 1) as Queue Name. Then click OK. Next please refer to the red rectangle for choosing the correct protocol and UPR name. Vigor2130 Series User’s Guide...
Page 22 If you do not know whether your printer is supported or not, please visit www.draytek.com to find out the printer list. Open Support >FAQ; find out the link of Printer Server and click it; then click the What types of printers are compatible with Vigor router? link.
Page 23: Basic Settings
The web page can be logged out according to the chosen condition. The default setting is Auto Logout, which means the web configuration system will logout after 5 minutes without any operation. Change the setting for your necessity. Vigor2130 Series User’s Guide...
Page 24: Changing Password
Note: The home page will change slightly in accordance with the type of the router you have. Go to System Maintenance page and choose System Password. Type a new password in New Password and Confirm New Password fields. Then click OK to continue. Vigor2130 Series User’s Guide...
Page 25: Quick Start Wizard
If your router can be under an environment with high speed NAT, the configuration provide here can help you to deploy and use the router quickly. The first screen of Quick Start Wizard is welcome page, please click Next. Vigor2130 Series User’s Guide...
Page 26: Setting Up The Password
The first screen of Quick Start Wizard is entering login password. After typing the password, please click Next. On the next page as shown below, please select the Time Zone for the router installed and specify the NTP server(s). Then click Next for next step. Vigor2130 Series User’s Guide...
Page 27: Setting Up The Internet Connection
IP, while a DSL service provider will offer a public subnet. If you have a public subnet, you could assign an IP address or many IP address to the WAN interface. Type the IP address. IP Address Type the subnet mask. Subnet Mask Vigor2130 Series User’s Guide...
Page 28 It is available when the box of Enable is checked. Click Clone Clone MAC Address PC Address. The result will be displayed in the field of MAC Address. After finishing the settings here, please click Next. Vigor2130 Series User’s Guide...
Page 29 MAC address cloning. It is available when the box of Enable is checked. Click Clone Clone MAC Address PC Address. The result will be displayed in the field of MAC Address. Vigor2130 Series User’s Guide...
Page 30 MAC address cloning. It is available when the box of Enable is checked. Click Clone Clone MAC Address PC Address. The result will be displayed in the field of MAC Address. Vigor2130 Series User’s Guide...
Page 31: Setting Up The Wireless Connection
It means the identification of the wireless LAN. SSID can be SSID any text numbers or various special characters. The default SSID is "DrayTek". We suggest you to change it. Select an appropriate encryption mode to improve the security Encryption and privacy of your wireless data packets.
Page 32 If you choose WPA-PSK as the security configuration, you have to specify WPA mode, algorithm and pre-shared key. The WPA encrypts each frame transmitted from the radio using Type the key, which either PSK (Pre-Shared Key) entered manually in this field below or automatically negotiated via 802.1x Vigor2130 Series User’s Guide...
Page 33 The WPA encrypts each frame transmitted from the radio using Type the key, which either PSK (Pre-Shared Key) entered manually in this field below or automatically negotiated via 802.1x authentication. Select WPA, WPA2 or Auto as WPA mode. Vigor2130 Series User’s Guide...
Page 34 Start PIN button. The WLAN LED on the router will blink fast when WPS is in progress. It will return to normal condition after two minutes. (You need to setup WPS within two minutes) After finishing the settings here, please click Next. Vigor2130 Series User’s Guide...
Page 35: Saving The Wizard Configuration
Drop PPPoE in the Online Status web page. Detailed explanation is shown below: LAN Status Displays the IP address of the LAN interface. IP Address Displays the total transmitted packets at the LAN interface. TX Packets Vigor2130 Series User’s Guide...
Page 36: Saving Configuration
Each time you click OK on the web page for saving the configuration, you can find messages showing the system interaction with you. Ready indicates the system is ready for you to input settings. Settings Saved means your settings are saved once you click Finish or OK button. Vigor2130 Series User’s Guide...
Page 37: Tutorials And Applications
If the router you have supports VoIP, you can configure VoIP WAN setting for using by VoIP interface of the router. In LAN VLAN setting, check the box of Enable (LAN to WAN in bridge mode) and type a different VLAN ID number. Vigor2130 Series User’s Guide...
Page 38 FXS 1 Phone connects to the FXS 1 port of Vigor2130, registers, sends and receives phone call with VoIP WAN. Functions Configuration 1. Open WAN>>Internet. Set PPPoE as the Connection Type and fill in the Username and Password offered by your ISP. Vigor2130 Series User’s Guide...
Page 39 2. Open WAN>>802.1Q VLAN Tag Configuration to configure Multi-VLAN. Refer to the following graphic. 3. Open WAN>>VoIP WAN to configure VoIP WAN Setting. Note: At present, only DHCP, PPPoE and Static connection types are available. Vigor2130 Series User’s Guide...
Page 40 4. Open VoIP >>SIP Accounts. Specify the connection interface for VoIP in the field of Register via. 5. Connect your PC or network device to the forth LAN port and type the username and password for PPPoE connection mode. Vigor2130 Series User’s Guide...
Page 41: Lan To Lan Ipsec Vpn Between Vigor2130 And Vigor2820 Using Main Mode
Enable it and give it a name. In this example the profile name is “Demo”. Enter Vigor2820’s WAN IP address in the Remote IP field. Select Main Mode as IKE phase 1 mode. Setup a pre-shared key, which must be the same as in Vigor2820. Vigor2130 Series User’s Guide...
Page 42 Accessing the VPN network of Vigor2820 from a PC behind Vigor2130 to initiate the VPN connection, for example, ping 192.168.1.x from a PC (192.168.30.x). Vigor2130 will be triggered to dial the IPSec VPN to Vigor2820. After the VPN is connected, you can monitor the status. Vigor2130 Series User’s Guide...
Page 43 In Dial-Out Settings part, select IPSec Tunnel and press the Advanced button. In Dial-In Settings part, please enable Specify Remote VPN Gateway and enter WAN IP address of Vigor2130 in the Peer VPN Server ID field. Vigor2130 Series User’s Guide...
Page 44 3DES, MD5; 3DES, SHA1; When you select AES(any) AES-256, MD5; AES-256, SHA1; When you select AES-128 AES-128, MD5; AES-128, SHA1; When you select AES-192 AES-192, MD5; AES-192, SHA1; When you select AES-256 AES-256, MD5; AES-256, SHA1; Vigor2130 Series User’s Guide...
Page 45: Case 2: Vpn Direction From Vigor2820 To Vigor2130
Enter Vigor2130’s private network in the Local Network / Mask field. Enter Vigor2820’s private network in the Remote Network / Mask field. Use default value “Automatic” for IKE phase 1 and phase 2 proposals. After the VPN is connected, you can monitor the status. Vigor2130 Series User’s Guide...
Page 46 Create a LAN-to-LAN profile. Enable it and give it a name. In this example the profile name is “test”. Vigor2130 Series User’s Guide...
Page 47 Name for VPN field. Setup a pre-shared key, which must be the same as in Vigor2130. Select ESP (High) and 3DES with Authentication. Enter Vigor2130’s private network in the Remote Network IP / Mask field. Click OK. Vigor2130 Series User’s Guide...
Page 48: Lan To Lan Ipsec Vpn Between Vigor2130 And Vigor2820 Using Agressive Mode
Create a LAN-to-LAN profile. Enable it and give it a name. In this example the profile name is “Demo”. Enter Vigor2820’s WAN IP address in the Remote IP field. Select Aggressive Mode as IKE phase 1 mode. Vigor2130 Series User’s Guide...
Page 49 10. Accessing the VPN network of Vigor2820 from a PC behind Vigor2130 to initiate the VPN connection, for example, ping 192.168.1.x from a PC (192.168.30.x). Vigor2130 will be triggered to dial the IPSec VPN to Vigor2820. After the VPN is connected, you can monitor the status. Vigor2130 Series User’s Guide...
Page 50 Create a LAN-to-LAN profile. Enable it and give it a name. In this example the profile name is “test”. Vigor2130 Series User’s Guide...
Page 51 3DES, MD5; 3DES, SHA1 When you select AES(any) AES-256, MD5; AES-256, SHA1 When you select AES-128 AES-128, MD5; AES-128, SHA1 When you select AES-192 AES-192, MD5; AES-192, SHA1 When you select AES-256 AES-256, MD5; AES-256, SHA1 Vigor2130 Series User’s Guide...
Page 52: Case 2: Vpn Direction From Vigor2820 To Vigor2130
Enter Vigor2130’s private network in the Local Network / Mask field. Enter Vigor2820’s private network in the Remote Network / Mask field. Use default value “Automatic” for IKE phase 1 and phase 2 proposals. 10. After the VPN is connected, you can monitor the status. Vigor2130 Series User’s Guide...
Page 53 Create a LAN-to-LAN profile. Vigor2130 Series User’s Guide...
Page 54 DES_SHA1_G2/3DES_MD5_G2/3DES_SHA1_G2” as IKE phase 1 proposal. Enter vigor2820 in the Local ID field. Click OK to return to the profile setting page. Enter Vigor2130’s private network in the Remote Network IP / Mask field. 10. Click OK. Vigor2130 Series User’s Guide...
Page 55: How To Configure Settings For Dlna Service In Vigor2130
Insert USB storage device into the USB slot of Vigor2130. Then, open USB Application>>Disk Status to check the connection status. If it is connected successfully, the general information of that device will be shown on the screen. Vigor2130 Series User’s Guide...
Page 56 During the process of installation, you can click Show Detail to view the installation procedure. After finished the service installation, the configuration page will be open automatically. Please click Enable and type a name in the field of Server Name. Then, click OK to activate DLNA service. Vigor2130 Series User’s Guide...
Page 57 Server Name configured in Step 4. Note: If you cannot see the media device in Network view, please check and make sure the UPnP service has been enabled Control Panel>>Administrative Tools >>Services. Vigor2130 Series User’s Guide...
Page 58 Before removing USB storage device, please DISABLE DLNA service and then remove the device. The audio and video files might not be played normally due to unrecognized equipment set in client. Vigor2130 Series User’s Guide...
Page 59: How To Download Bt Torrent To Usb Device Via Vigor Router
Wait for few seconds for the router to detect it. If the disk is detected, it will be shown as the following figure. Make sure that WAN connection has been established. Open USB Application >> Bit Torrent Download. Click Install to install BT module from Internet to USB device. Vigor2130 Series User’s Guide...
Page 60 Simply wait for a few minutes to finish the installation. When the installation is finished, the following page will be displayed. Click the link of Open Web Client to open another window. Vigor2130 Series User’s Guide...
Page 61 10. Click Select File to open the following dialog. Choose the seed of BT torrent file and click Open. Note: Before uploading torrent files to the router, please search from Internet and store the seed of the BT torrent on our hard disk first. Vigor2130 Series User’s Guide...
Page 62 Access into Vigor2130 web configuration interface and open USB Application >> USB General Settings. Enable the Disk Sharing function by checking the box and click OK. Open USB Application >> Disk Shares. Click Add a New Entry. Vigor2130 Series User’s Guide...
Page 63 Share Name for home folder (“/”) . Click OK. Now, PCs in LAN connected to Vigor2130 can open a browser from his / her computer. Simply type “\\192.168.1.1” in the field of Address and then click Go. Vigor2130 Series User’s Guide...
Page 64 The sharing disk with the name of “bt_folder” created above will be shown as the following figure. Double click bt_folder to view the files in the disk. Vigor2130 Series User’s Guide...
Page 65 If you want to check the BT Torrent files downloaded from Internet to USB disk, access into bt_folder>>downloads. (Note: While the file is downloading, the file extension name will be “part”.) Vigor2130 Series User’s Guide...
Page 66: How To Configure Dynamic Dns Service On Vigor2130
Vigor2130. Go to http://freedns.afraid.org/dynamic/ and login with your normal username and password for the FreeDNS service. Click Direct URL on the domain, you would like to set to your WAN IP address. Vigor2130 Series User’s Guide...
Page 67 Past the strings what you copied on step3 on password field. Click OK to save the configuration. Now, you can check the service by using nslookup command on your computer or check the syslog information on Vigor2130. Vigor2130 Series User’s Guide...
Page 68 This page is left blank. Vigor2130 Series User’s Guide...
Page 69: Web Configuration
These are known as private IP addresses, and are listed in the following ranges: From 10.0.0.0 to 10.255.255.255 From 172.16.0.0 to 172.31.255.255 From 192.168.0.0 to 192.168.255.255 Vigor2130 Series User’s Guide...
Page 70 After connecting into the router, 3G USB Modem will be regarded as the backup WAN port. Therefore, when WAN is not available, the router will use 3.5G for supporting automatically. The supported 3G USB Modem will be listed on DrayTek web site. Please visit www.draytek.com for more detailed information.
Page 71: Internet Access
WAN interface, please use WAN IP Alias. You can set up to 8 public IP addresses other than the current one you are using. Such function can be applied to each connection type. Vigor2130 Series User’s Guide...
Page 72 If you have a public subnet, you could assign an IP address or many IP address to the WAN interface. To use Static as the accessing protocol of the internet, please choose Static mode from Connection Type drop down menu. The following web page will be shown. Vigor2130 Series User’s Guide...
Page 73 Ping IP IP address in this field for pinging. It is available when the box of Enable is checked. Click Clone Clone MAC Address MAC Address. The result will be displayed in the field of MAC Address. Vigor2130 Series User’s Guide...
Page 74 Type in a name for the router. It must be the same as the name Router Name used in Syslog. Type the domain name (e.g., draytek) to fit the request of some Domain Name ISPs. It means Max Transmit Unit for packet. The default setting will MTU Size be specified by the system automatically.
Page 75 Type in a fixed IP address in the box if you click Yes for Fixed Fixed IP Address (IPCP) IP(IPCP). Such function allows you to verify whether network connection Mode is alive or not through ARP Detect or Ping Detect. Choose ARP Vigor2130 Series User’s Guide...
Page 76 Connection Type drop down menu. The following web page will be shown. Type in the username provided by ISP in this field. Username Type in the password provided by ISP in this field. Password Type in the IP address for PPTP /L2TP server. Server Address Vigor2130 Series User’s Guide...
Page 77 It is available when the box of Enable is checked. Click Clone Clone MAC Address MAC Address. The result will be displayed in the field of MAC Address. After finishing all the settings here, please click OK to activate them. Vigor2130 Series User’s Guide...
Page 78 It is available when the box of Enable is checked. Click Clone Clone MAC Address MAC Address. The result will be displayed in the field of MAC Address. After finishing all the settings here, please click OK to activate them. Vigor2130 Series User’s Guide...
Page 79 It is available when the box of Enable is checked. Click Clone Clone MAC Address MAC Address. The result will be displayed in the field of MAC Address. After finishing all the settings here, please click OK to activate them. Vigor2130 Series User’s Guide...
Page 80: Multi-Vlan
Vigor2130 series offers multi-VLAN function to make the data transmission with security. Data transmitting through the Ethernet port for connecting to Internet can be tagged with an ID number specified here for ensuring the security. In addition, each LAN port also can be tagged with an ID number in local network to reach the goal of protection.
Page 81 Type the IP address of secondary DNS server obtained from Secondary DNS Server ISP for the usage of VoIP. When DHCP is selected as connection type, you need to configure the following settings: Type the name of the router. Router Name Vigor2130 Series User’s Guide...
Page 82: Ports
It displays current speed that the router uses. Speed Current You can use the drop down list to choose the required speed Speed Configured for the router. If you have no idea in configuring speed, simple use the default setting, Auto. Vigor2130 Series User’s Guide...
Page 83 The Configured column allows for changing the power Power Control savings mode parameters per port. Disabled: All power savings mechanisms disabled. ActiPHY: Link down power savings enabled. PerfectReach: Link up power savings enabled. Enabled: Both link up and link down power savings enabled. Vigor2130 Series User’s Guide...
Page 84: Backup
PPP Username Type the PPP password (optional). PPP Password It is available when the box of Enable is checked. Click Clone MAC Address Clone MAC Address. The result will be displayed in the field of MAC Address. Vigor2130 Series User’s Guide...
Page 85 Check this box to enable such function. Enable 56K Backup Type the phone number offered by the ISP for dial-out Phone Number connection. Type the PPP username (optional). PPP Username Type the PPP password (optional). PPP Password Vigor2130 Series User’s Guide...
Page 86: Lan
IP address. As a part of the public subnet, the Vigor router will serve for IP routing to help hosts in the public subnet to communicate with other public hosts or servers outside. Therefore, the router should be set as the gateway for public hosts. Vigor2130 Series User’s Guide...
Page 87 You can group local hosts by physical ports and create up to 4 virtual LANs. To manage the communication between different groups, please set up rules in Virtual LAN (VLAN) function and the rate of each. Vigor2130 Series User’s Guide...
Page 88: General Setup
2nd subnet. Check the box to enable DHCP server setting. Enter a value of the IP address pool for the DHCP server to Start IP Address start with when issuing IP addresses. If the 2nd IP address of Vigor2130 Series User’s Guide...
Page 89 Otherwise, the router forwards the DNS query packet to the external DNS server by establishing a WAN (e.g. DSL/Cable) connection. After finishing all the settings here, please click OK to activate them. Vigor2130 Series User’s Guide...
Page 90: Ports
Current Tx: indicates whether pause frames on the port are transmitted. This module offers 1518~9600 (Bytes) length to make the Maximum Frame long packet for data transmission. There are two modes for you to choose when excessive Excessive Collision Mode collision happened in half-duplex condition. Vigor2130 Series User’s Guide...
Page 91 PerfectReach: Link up power savings enabled. Enabled: Both link up and link down power savings enabled. Click this button to refresh the information for WAN port. Refresh After finishing all the settings here, please click OK to activate them. Vigor2130 Series User’s Guide...
Page 92: Mac Address Table
To add a new static MAC entry, click Add new static entry. A new entry will be shown as follows. Choose a VLAN ID and type a new MAC address. Next, specify port member for this table. Finally, click OK to save the changes. Vigor2130 Series User’s Guide...
Page 93: Vlan
To add or remove a VLAN, please refer to the following example. VLAN 1 is consisted of hosts linked to P1 ~ P4. After checking the box to enable VLAN function, you will check the table according to the needs as shown below. Vigor2130 Series User’s Guide...
Page 94: Monitor Port
Monitor ingress port monitors the packets received by the port you set up. Check to set up the port(s) for being monitored. It only Monitor egress port monitors the packets transmitted by the port you set up. Vigor2130 Series User’s Guide...
Page 95: Static Route
Main Router 192.168.1.1 as the default gateway for the Router A 192.168.1.2. Before setting Static Route, user A cannot talk to user B for Router A can only forward recognized packets to its default gateway Main Router. Vigor2130 Series User’s Guide...
Page 96 192.168.1.2. Click OK. Return to Static Route page. Click Add again to add another static route as show below, which regulates all packets destined to 211.100.88.0 will be forwarded to 192.168.1.3. Verify current routing table. Vigor2130 Series User’s Guide...
Page 97: Bind Ip To Mac
It is used to refresh the ARP table. When there is one new Refresh PC added to the LAN, you can click this link to obtain the newly ARP table information. It displays a list for the IP bind to MAC information. IP Bind List Vigor2130 Series User’s Guide...
Page 98: Nat
192.168.1.0/24 subnet for the router. As stated before, the NAT facility can map one or more IP addresses and/or service ports into different specified services. In other words, the NAT function can be achieved by using port mapping methods. Below shows the menu items for NAT. Vigor2130 Series User’s Guide...
Page 99: Hardware Nat
Hardware-base Acceleration Engine, also named Protocol Processing Engine API is the function that DrayTek provides to extremely speed up the NAT performance. While the hardware acceleration mechanism is activated, most of the bandwidth usage will be concentrated on the specific sessions which increase transmission speed to get ultimately accelerated.
Page 100 Enter the private IP address of the local host. Local Host If it is configured, the forwarded traffic is mapped to this Local Port (optional) port on the local host. Click OK to save the settings. Vigor2130 Series User’s Guide...
Page 101: Dmz Host
Enter the private IP address of the DMZ host, or click Private IP Choose PC to specify a suitable one. Bring a dialog for you to choose an IP address. Choose PC Click OK to save the settings. Vigor2130 Series User’s Guide...
Page 102: Firewall
Check this box to enable storm control status for the frame Status type. The unit is packet per second (pps). Use the drop down list Rate Vigor2130 Series User’s Guide...
Page 103: Ports Configuration
Select whether forwarding is permitted ("Allow") or denied Action ("Deny"). The default value is "Allow". Select a rate limiter to apply to this port. Available settings Rate Limiter ID include Disabled, and 1 to 10. The default value is Disabled. Vigor2130 Series User’s Guide...
Page 104 Rate limiter ID will be applied to WAN port and LAN port. Rate Limiter ID Please specify a rate number for each ID. The default setting is “1”(packet per second). Define the rate by choosing from the following drop down Rate list. Vigor2130 Series User’s Guide...
Page 105 Click OK to save the settings. Vigor2130 Series User’s Guide...
Page 106: Access Control List
Policy ID might have more than one port grouped. Frame Type - Such option differs according to the selection you choose, we will explain it in detailed later. Action – it means the session limitation for this access control Vigor2130 Series User’s Guide...
Page 107 Choose Any to set the parameter with any value set by the Ethernet Type Filter router automatically or choose Specific to specify certain value (the range is 0x0000 to 0xFFFF). Choose ARP as the Frame Type, you will get ARP Parameters option as the following: Vigor2130 Series User’s Guide...
Page 108 Choose Host to filter the packets from the host with the address typed in Target IP Address filed. Choose Network to filter the packets within the network defined in Target IP Address and Target IP Mask fields. Vigor2130 Series User’s Guide...
Page 109 Ethernet (0x06) and the protocol address length is equal to IPv4 (0x04) must match this entry. Any: Any value is allowed Specify whether frames/packets can meet the action according to their ARP/RARP hardware address space (HRD) settings. Vigor2130 Series User’s Guide...
Page 110 Type the Source IP Address here. This option is available Source IP Address when you choose Host or Network as Source IP. Type the Source IP Mask here. This option is available Source IP Mask only when you choose Network as source Source IP. Vigor2130 Series User’s Guide...
Page 111 0 to 255. A frame meeting this ACE matches this ICMP value. Choose IPv4 as the Frame Type. You will see IP Parameters on the bottom of the page. If you choose UDP as IP Protocol Filter, you will get the page as the following: Vigor2130 Series User’s Guide...
Page 112 Type the DIP Mask here. This option is available only Dest IP Mask when you choose Network as destination DIP. Specify the UDP port source filter for this ACE. Source Port Filter Any: No UDP source filter is specified. Vigor2130 Series User’s Guide...
Page 113 ACE matches this UDP source value. Type the value if you choose Range as the Dest. Port Filter. Dest. Port Range The allowed range is 0 to 65535. A frame meeting this ACE matches this UDP source value. Vigor2130 Series User’s Guide...
Page 114 Dest IP Address available when you choose Host or Network as destination IP filter. Type the destination IP Mask here. This option is available Dest IP Mask only when you choose Network as destination IP filter. Vigor2130 Series User’s Guide...
Page 115 0: TCP frames where the FIN field is set must not be able to match this entry. 1: TCP frames where the FIN field is set must be able to match this entry. Any: Any value is allowed. Vigor2130 Series User’s Guide...
Page 116 Any: Any value is allowed Specify the TCP "Urgent Pointer field significant" (URG) TCP URG value for this ACE. 0: TCP frames where the URG field is set must not be able to match this entry. Vigor2130 Series User’s Guide...
Page 117 Host: Destination IP filter is set to Host. Specify the destination IP address in the destination IP Address field that appears. Network: Destination IP is set to Network. Specify the destination IP address and destination IP mask in the Vigor2130 Series User’s Guide...
Page 118: Traffic Control
You are allowed to add many firewall rules for your request. Simply click Add Entry, the following screen will be shown. Check the box to enable such rule. Enable Type a name of the rule for identification. Name Vigor2130 Series User’s Guide...
Page 119 New Time Object – Such link allows you to create new time object for using by web feature filter. The method to configure the time object is that same as set in Firewall>>Time Object. Click OK to save the settings. Vigor2130 Series User’s Guide...
Page 120: Csm
Time –Specify a period for filtering the packets with web feature filter. Use the drop down list to choose the time setting, or click New Time Object to define a time period for you necessity. Vigor2130 Series User’s Guide...
Page 121 OK, it will be filtered whenever you visit. Type the host name of URL for filtering. Click Add a New Web Host Filter Setting Entry to add the host name of URL one by one. Vigor2130 Series User’s Guide...
Page 122: Web Content Filter
Open CSM>>Web Content Filter. The following page will be displayed. Type the required information such as source IP address and subnet mask. Check the items that you want to filter. After finishing the general settings, please click Activate to activate Commtouch WCF mechanism. Vigor2130 Series User’s Guide...
Page 123: App Enforcement
You can send a report for mistaken classified URL to Misclassified Report Commtouch by clicking such link. You can define policy profiles for IM (Instant Messenger)/P2P (Peer to Peer)/Protocol application. This page allows you to set 32 profiles for different requirements. Vigor2130 Series User’s Guide...
Page 124 You are allowed to add many firewall rules for your request. Simply click Add Entry, the following screen will be shown. There are four tabs IM, P2P, Protocol and Misc displayed on this page. Each tab will bring out different items that you can choose to disallow/allow people using. Vigor2130 Series User’s Guide...
Page 125: Bandwidth Management
Firewall>>Time Object. Simply check the box(s) that you want to block and click OK to save the settings. Below shows the menu items for Bandwidth Management. Vigor2130 Series User’s Guide...
Page 126: Session Limit
Adds the specific session limitation onto the list above. Allows you to edit the settings for the selected limitation. Edit Remove the selected settings existing on the limitation list. Delete When you finish adding a new session limit, simply click OK. Vigor2130 Series User’s Guide...
Page 127: Bandwidth Limit
Limitation List - Display a list of specific limitations that you set on this web page. Start IP - Bandwidth limit can be applied on certain IP range. That’s, only the PCs within the range will be Vigor2130 Series User’s Guide...
Page 128 Add - Add the specific speed limitation onto the list above. Edit - Allows you to edit the settings for the selected limitation. Delete - Remove the selected settings existing on the limitation list. When you finish adding a new bandwidth limit, simply click OK. Vigor2130 Series User’s Guide...
Page 129: Port Rate Control
(or in another term “dropped”) from an overflowing queue, packets of sensitive applications mentioned above might be the ones to drop off. How this will affect application performance? There are two components within Primary configuration of QoS deployment: Vigor2130 Series User’s Guide...
Page 130 SLA among different DS domain owners. It’s not easy to achieve deterministic and consistent high-priority QoS traffic throughout the whole network with merely Vigor router’s effort. In the Bandwidth Management menu, click QoS Control List to open the web page. Vigor2130 Series User’s Guide...
Page 131 QCE onto this page. Different QCE type will bring out different web settings. If you choose Ethernet Type as QCE Type, you have to type value for it and specify traffic class from Low, Normal, Medium and High. Vigor2130 Series User’s Guide...
Page 132 Type in the starting port number and the end porting number TCP/UDP Port Range here if you choose Range as the type. Vigor2130 Series User’s Guide...
Page 133 If you choose ToS as QCE Type, you have to specify priority class from Low, Normal, Medium and High. If you choose Tag Priority as QCE Type, you have to specify priority class from Low, Normal, Medium and High. Click to modify the settings of an existing QCE on this page. Vigor2130 Series User’s Guide...
Page 134: Ports Priority
Default Class Use the drop down list to choose the QCL number defined in QCL (QoS Control List ) QoS Control List for the port. Use the drop down list to choose suitable mode. Queuing Mode Vigor2130 Series User’s Guide...
Page 135: Qos Statistics
Queue Weighted weighted number. Click OK to save the settings. This page displays statistics for QoS setting. Click WAN/LAN link to check detailed information for each interface. Click WAN/LAN link to check detailed information for each interface. Vigor2130 Series User’s Guide...
Page 136 Display the number of 512 ~ 1023-byte frames in good and RX 512-1023 Bytes bad packets received. Display the number of 1024-1522-byte frames in good and RX 1024- 1526 Bytes bad packets received. Display the number of 1527-byte frames in good and bad RX 1527 Bytes Vigor2130 Series User’s Guide...
Page 137 Display the number of 1527-byte frames in good and bad Tx 1527 Bytes: packets transmitted. Display the low queue counter of the packet transmitted. Tx Low Display the normal queue counter of the packet transmitted. Tx Normal Vigor2130 Series User’s Guide...
Page 138: Applications
DDNS service providers such as www.dyndns.org, www.no-ip.com, www.dtdns.com, www.changeip.com, www.dynamic- nameserver.com. You should visit their websites to register your own domain name for the router. Check this box to enable the current account. Enable Dynamic DNS Vigor2130 Series User’s Guide...
Page 139: Schedule
You can inquiry an NTP server (a time server) on the Internet to synchronize the router’s clock. This method can only be applied when the WAN connection has been built up. You can set up to 15 schedules. To add a schedule profile, please click Add. Vigor2130 Series User’s Guide...
Page 140 Acts Once -The schedule will be applied just once. Routine /Weekday -Specify which days in one week should perform the schedule. Click OK button to activate the settings. You will see your setting has been saved. Vigor2130 Series User’s Guide...
Page 141: Igmp
Check the box to enable unregistered IPMC traffic flooding. Unregistered IPMC Flooding enabled Check the box to fast leave from the LAN port. Fast Leave Click OK button to activate the settings. You will see your setting has been saved. Vigor2130 Series User’s Guide...
Page 142: Igmp Status
Windows XP and the router provide the associated support for MSN Messenger to allow full use of the voice, video and messaging features. Enable UPnP function. You have to type the download and Enable UPnP upload speed. Vigor2130 Series User’s Guide...
Page 143 Subsequently, such a facility forwards packets from the external ports of the router to the internal ports used by the application. The reminder as regards concern about Firewall and UPnP Can't work with Firewall Software Vigor2130 Series User’s Guide...
Page 144: Wake On Lan
IP to MAC will be shown in this drop down list. Choose the IP address from the drop down list that you want to wake up. Type any one of the MAC address of the bond PCs. MAC Address Vigor2130 Series User’s Guide...
Page 145: Vpn And Remote Access
VPN (PPTP) remote access from WAN side to the router. IP Address range for PPTP client – Specify an IP address pool for the local private network that will be assigned to PPTP clients. Note the values given here should not be the Vigor2130 Series User’s Guide...
Page 146: Pptp Remote Dial-In
VPN connection. The router provides access accounts for dial-in users. Note: This page is similar to the page under User>>User Configuration. Click Add a New User to open the following page. Vigor2130 Series User’s Guide...
Page 147 Check this box to let the remote user to adjust the settings of Allow TELNET router by TELNET. When you finish the settings, simply click OK to save the configuration. The new user will be created and displayed on the page. Vigor2130 Series User’s Guide...
Page 148 To edit a user, click the name link under Username to open the following page. Modify the settings except Username and then click OK to save and exit it. If you want to remove such user settings, simply click Delete User. Vigor2130 Series User’s Guide...
Page 149: Ipsec Remote Dial-In
Example: 10.10.137.240-10.10.137.245. If you choose this type, please specify the IP address range for L2TP/IPSec mode. Shared secret – Type the shared secret manually and confirm Authentication it again. IPSec remote dial-in clients will use the given secret. Vigor2130 Series User’s Guide...
Page 150: Remote Dial-In Status
Display the status of the phase 1 ISAKMP key exchange. IKE Status the encryption and authentication algorithm used Display IKE Alg during phase 1 of the VPN connection Establishment. The algorithm is used during exchange of key exchange. Vigor2130 Series User’s Guide...
Page 151 Display the data total received for such client. Rx bytes Display the data total transmitted for such client. Tx bytes Check this box to make the system refresh this page Auto-refresh automatically. Click this button to refresh the page immediately. Refresh Vigor2130 Series User’s Guide...
Page 152: Lan To Lan
Rx Packets / Rx Bytes (by IPSec or PPTP). Display the duration time of the IPSec / PPTP connection. Up Time Click it to add a new VPN tunnel via IPSec / PPTP protocol. Add Tunnel Vigor2130 Series User’s Guide...
Page 153 IPSec session. However, the Aggressive mode is faster. The default value in Vigor router is Main mode. Such field will be applicable when Pre-shared key is selected Pre-Shared Key as the Type for the authentication. Input 1-63 characters as pre-shared key. Vigor2130 Series User’s Guide...
Page 154 The IKE Phase 1 key will be reused to avoid the computation Perfect Forward Secrecy complexity in phase 2. The default value is inactive this function. Click OK to save the settings. Vigor2130 Series User’s Guide...
Page 155 Remote Network / Mask Network IP Address/Remote Network Mask through the VPN connection. If the remote network only allows you to dial in with single IP, Route/NAT Mode please choose NAT Mode, otherwise please choose Route Mode. Vigor2130 Series User’s Guide...
Page 156: Wireless Lan
Point (AP) connecting to lots of wireless clients or Stations (STA). All the STAs will share the same Internet connection via Vigor wireless router. The General Settings will set up the information of this wireless network, including its SSID as identification, located channel etc. Vigor2130 Series User’s Guide...
Page 157 /or privacy on your wireless network. The Vigor wireless router is very flexible and can support multiple secure connections with both WEP and WPA at the same time. Below shows the menu items for Wireless LAN. Vigor2130 Series User’s Guide...
Page 158: General Setup
It means the identification of the wireless LAN. SSID can be SSID any text numbers or various special characters. The default SSID is "DrayTek". We suggest you to change it. Check this box to make the wireless clients (stations) not Isolate LAN accessing the PC with wired connection.
Page 159 Select an appropriate encryption mode to improve the security Encryption and privacy of your wireless data packets. Each encryption mode will bring out different web page and ask you to offer additional configuration. Click OK to save the settings. Vigor2130 Series User’s Guide...
Page 160 Accepts only WPA clients and the encryption key should be entered in PSK. The WPA encrypts each frame transmitted from the radio using the key, which either PSK (Pre-Shared Key) entered manually in this field below or automatically negotiated via 802.1x authentication. Vigor2130 Series User’s Guide...
Page 161 The WPA encrypts each frame transmitted from the radio Type using the key, which either PSK (Pre-Shared Key) entered manually in this field below or automatically negotiated via 802.1x authentication. Select WPA, WPA2 or Auto as WPA mode. Vigor2130 Series User’s Guide...
Page 162 Users do not need to select any encryption mode and type any long encryption passphrase to setup a wireless client every time. He/she only needs to press a button on wireless client, and WPS will connect for client and router automatically. Vigor2130 Series User’s Guide...
Page 163 Start PBC button or using PIN Code. On the side of Vigor2130 series which served as an AP, press WPS button once on the front panel of the router or click Start PBC on web configuration interface. On the side of a station with network card installed, press Start PBC button of network card.
Page 164: Access Control
Delete the selected MAC address in the list. This button will Delete appear only an entry of MAC Address has been typed. Click OK to save the configuration. Station List provides the knowledge of connecting wireless clients now along with its status code. Vigor2130 Series User’s Guide...
Page 165: Access Point Discovery
Display the SSID of the scanned AP. SSID Display the MAC address of the scanned AP. BSSID Display the encryption type of the scanned AP. Security Display the strength (in percentage) of the signal of the Signal scanned AP. Vigor2130 Series User’s Guide...
Page 166: Wmm Configuration
AC_VI and AC_VO categories For the service of e-mail or web browsing, please set large value for AC_BE and AC_BK categories. CWMin means contention Window-Min and CWMax means CWMin/CWMax contention Window-Max. Please specify the value ranging Vigor2130 Series User’s Guide...
Page 167 It can assure that the peer must receive the WMM packets. “Check” the box means the AP router will not answer any response request for the transmitting packets. It will have better performance with lower reliability. Click OK to save the settings. Vigor2130 Series User’s Guide...
Page 168: Wds
To meet the above requirement, two WDS modes are implemented in Vigor router. One is Bridge, the other is Repeater. Below shows the function of WDS-bridge interface: The application for the WDS-Repeater mode is depicted as below: Vigor2130 Series User’s Guide...
Page 169 Type 8 ~ 63 ASCII characters or 64 hexadecimal digits leading by “0x”. Four peer MAC addresses are allowed to be entered in this Peer Mac Address page at one time. Vigor2130 Series User’s Guide...
Page 170: Usb Application
USB port in router, please check the box of Safely Remove Disk first. And then, remove the USB storage disk later. Check this box and then you can remove the USB disk Safely Remove Disk safely. Vigor2130 Series User’s Guide...
Page 171: File Explorer
Click this icon to add a new folder. Create Display current folder. Current Path Click this button to upload the selected file to the USB Upload diskette. The uploaded file in the USB diskette can be shared for other user through FTP. Vigor2130 Series User’s Guide...
Page 172: Ftp User Management
USB diskette. In addition, if the user types “/” here, he/she can access into all of the disk folders and files in USB diskette. Note: When write protect status for the USB diskette is ON, you cannot type any new folder name in this field. Vigor2130 Series User’s Guide...
Page 173: Disk Shares
It displays the directory name for the connected USB disk. Path It displays the status of the connected USB disk. Visible To add a new entry for disk sharing, please click Add a New Entry to open the following page. Vigor2130 Series User’s Guide...
Page 174 USB disk. All Users Read-only - everyone has read-only access to the share disk. All Users Read-write - everyone has read-write access to the share disk. Specific Users – Only specific user(s) can access into the Vigor2130 Series User’s Guide...
Page 175: Bit Torrent Download
USB storage device directly. Click USB Application >>Bit Torrent Download. Click Install to install the BT module for the router and the USB storage device. When the module installation is finished, you will see the following screen: Vigor2130 Series User’s Guide...
Page 176 Disable – Click it to disable authentication function. Type a name for authentication. User Name Type a password for authentication. Password Type a port number for accessing Open Web Client. Web Client Port Vigor2130 Series User’s Guide...
Page 177: Itunes Server
The default name is the router name. You can change it if Server Name needed. After storing the media files in the USB storage device, Path please specify a path for the files to be accessed for iTunes Vigor2130 Series User’s Guide...
Page 178: Dlna Server
When the server installation is finished, you will see the following screen: Enable – Click it to enable DLNA Server function. DLNA Server Disable – Click it to disable DLNA Server function. The default name is the router name. You can change it if Server Name Vigor2130 Series User’s Guide...
Page 179: Voip
Then, both parties’ SIP proxies will forward the sequence of messages to caller to establish the session. If you both register to the same SIP Registrar, then it will be illustrated as below: Vigor2130 Series User’s Guide...
Page 180: Dialplan
This page allows you to set phone book and digit map for the VoIP function. Click the Phone Book, Digit Map, Call Barring and Regional links on the page to access into next pages for dialplan settings. Vigor2130 Series User’s Guide...
Page 181 SIP addresses. Loop through and Backup Phone Number will be displayed if you are using Vigor2820V for setting the phone book. Click any index number to display the dial plan setup page. Vigor2130 Series User’s Guide...
Page 182 VoIP interface. Take the above picture (Prefix Table Setup web page) as an example, the OP number of 886 will be deleted completely for the prefix number is set Vigor2130 Series User’s Guide...
Page 183 Choose the one that you want to enable the prefix number Route settings from the saved SIP accounts. Please set up one SIP account first to make this interface available. This item will be changed according to the port settings configured in VoIP>> Phone Settings. Vigor2130 Series User’s Guide...
Page 184 Determine the direction for the phone call, IN – incoming Call Direction call, OUT-outgoing call, IN & OUT – both incoming and outgoing calls. Determine the type of the VoIP phone call, URI/URL or Barring Type number. Vigor2130 Series User’s Guide...
Page 185 SIP accounts. Such control also can be done based on preconfigured schedules. For Block IP Address – this function can block incoming calls (through Phone port) coming from IP address. Such control also can be done based on preconfigured schedules. Vigor2130 Series User’s Guide...
Page 186 Dial the number typed in this field to release the DND Do Not Distrub [Deact] function. Dial the number typed in this field to make your phone Hide caller ID [Act] number (ID) not displayed on the display panel of remote Vigor2130 Series User’s Guide...
Page 187: Sip Accounts
Display the domain name or IP address of the SIP proxy Proxy server. Display the account name of SIP address before @.. Account Name Specify which port will ring when receiving a phone call. Ring Port Vigor2130 Series User’s Guide...
Page 188 The system will select a proper way for your VoIP call. Set the port number for sending/receiving SIP message for SIP Port building a session. The default value is 5060. Your peer must set the same value in his/her Registrar. Vigor2130 Series User’s Guide...
Page 189 SIP Registrar again. Set Phone 1 and/or Phone 2 as the default ring port(s) for this Ring Port SIP account. Choose a ring tone type for the VoIP phone call. Ring Pattern Vigor2130 Series User’s Guide...
Page 190: Phone Settings
Advanced setting allows you to adjust tone settings manually if you choose User Defined. TOn1, TOff1, TOn2 and TOff2 mean the cadence of the tone pattern. TOn1 and TOn2 represent sound-on; TOff1 and TOff2 represent the sound-off. Vigor2130 Series User’s Guide...
Page 191 Dynamic RTP Port End - Specifies the end port for RTP stream. The default value is 15000. RTP TOS – It decides the level of VoIP package. Use the drop down list to choose any one of them. Vigor2130 Series User’s Guide...
Page 192 During the period, the one who dial in will mode listen busy tone, yet the local user will not listen any ring tone. Check this box to hide the caller ID on the display panel of CLIR (hide caller ID) Vigor2130 Series User’s Guide...
Page 193 This function can detect if the voice on both sides is active Voice Active Detection or not. If not, the router will do something to save the bandwidth for other using. Click On to invoke this function; click off to close the function. Vigor2130 Series User’s Guide...
Page 194 DTMF Mode – There are four DTMF modes for you to DTMF choose. InBand - Choose this one then the Vigor will send the DTMF tone as audio directly when you press the keypad on the phone Vigor2130 Series User’s Guide...
Page 195: Status
HANG_UP - Indicates that the connection is not established (busy tone). CONNECTING - Indicates that the user is calling out. WAIT_ANS - Indicates that a connection is launched and waiting for remote user’s answer. ALERTING - Indicates that a call is coming. Vigor2130 Series User’s Guide...
Page 196: Ipv6
The volume of present call. Speaker Gain Display logs of VoIP calls. This page defines the IPv6 connection types for WAN interface. Possible types contain Link-Local only, Static IPv6, DHCPv6 and TSPC. Each type requires different parameter settings. Vigor2130 Series User’s Guide...
Page 197 EUI-64 format. Display the fixed value (64) for prefix length. Prefix Length This type allows you to setup static IPv6 address for WAN. Type your IPv6 static IP here. IPv6 Address Vigor2130 Series User’s Guide...
Page 198 It is used by an individual organization to create its own SLA ID local addressing hierarchy and to identify subnets. Tunnel setup protocol client (TSPC) is an application which could help you to connect to IPv6 network easily. Vigor2130 Series User’s Guide...
Page 199 IPv6-in-IPv4 (NAT Traversal - Request an IPv6 in UDP of IPv4 tunnel (for clients behind a NAT). After passing the time set here, the client will retry to Auto-reconnect Delay connect in case of failure or keepalive timeout. 0 means not retry. Vigor2130 Series User’s Guide...
Page 200 Type the password again to make the confirmation. Confirm Password Type the default server address, tic.sixxs.net. Server Choose one of the tunnel modes Tunnel mode AYIYA – allows tunnels to be created even behind firewalls and NAT's. Vigor2130 Series User’s Guide...
Page 201: Ipv6 Lan Setup
Vigor2130 provides 2 daemons for LAN side IPv6 address Configuration Type configuration. One is RADVD(stateless) and the other is DHCPv6 Server (Stateful). DHCPv6 Server- DHCPv6 Server could assign IPv6 address to PC according to the Start/End IPv6 address configuration. Vigor2130 Series User’s Guide...
Page 202: Ipv6 Firewall Setup
Display the source IP address of such rule. Source IP Display the destination IP address of such rule. Destination IP Display the source port number of such rule. Source Port Display the destination port number of such rule Destination Port Vigor2130 Series User’s Guide...
Page 203 Type the subnet mask here if you choose Subnet as Source Source Subnet IP Type. Type the subnet mask here if you choose Subnet as Source IP Type. Determine the IP type as the destination. Destination IP Type Vigor2130 Series User’s Guide...
Page 204 You are using IPv6 from 2001:5c0:1503:7400:30e4:139d:53c8:3a1e Set firewall rule to block all TCP traffic from this IP address. Open IPv6 >> IPv6 Firewall Setup and press Add New Rule. In the following dialog, please configure the page with the following values. Vigor2130 Series User’s Guide...
Page 205: Ipv6 Routing
The IPv6 address prefix. Prefix distance to the target (usually counted in Display the Metric hops). It is not used by recent kernels, but may be needed by routing daemons. Vigor2130 Series User’s Guide...
Page 206: Ipv6 Neighbour
- neighbor may be unreachable and a packet was sent. probe - neighbor may be unreachable and probes are sent to verify the reachability. Check this box to enable an automatic refresh of the page at Auto-refresh regular intervals. Vigor2130 Series User’s Guide...
Page 207: Ipv6 Tspc Status
When the router detects all the information, the screen will be shown as follows. One set of TSPC prefix and prefix length will be obtained after the connection between TSPC and Tunnel broker built. Vigor2130 Series User’s Guide...
Page 208 When the router connects to the tunnel broker, the router will use RADVD to transmit the prefix to the PC on LAN. Next, the PC will generate one set of IPv6 public IP (see the figure below). Users can use such IP for connecting to IPv6 network. Vigor2130 Series User’s Guide...
Page 209: Ipv6 Management
Enable the checkbox to allow system administrators to login Enable from the Internet. There are several servers provided by the HTTP/HTTPS/SSH/ICMP system to allow you managing the router from Internet. Ping/FTP/TELNET Check the box(es) to specify. Vigor2130 Series User’s Guide...
Page 210: User
Type full name for this user. Full Name Type the password for this user. Password Type the password again for confirmation. Confirm Password Check this box to have the remote user share the disk Allow Disk Sharing information. Vigor2130 Series User’s Guide...
Page 211 To edit a user, click the name link under Username to open the following page. Modify the settings except Username and then click OK to save and exit it. If you want to remove such user settings, simply click Delete User. Vigor2130 Series User’s Guide...
Page 212: System Maintenance
For the system setup, there are several items that you have to know the way of configuration: Status, User Password, Configuration Backup, Syslog/Mail Alert, Time and Date, Management, Reboot System, and Firmware Upgrade. Below shows the menu items for System Maintenance. Vigor2130 Series User’s Guide...
Page 213: System Status
IPv6 Address (Link) Display if the DHCP server is active or not. DHCP Server WAN------- Display current connection type used. Connection Mode Display the connection status. Link Status Display the MAC address of the WAN Interface. MAC Address Vigor2130 Series User’s Guide...
Page 214 Display the channel that wireless LAN used. Channel Display the manufacturer of the disk. Manufacturer Display the model of the disk. Model Display the storage size of the USB diskette. Size Display current status of the USB diskette. Status Vigor2130 Series User’s Guide...
Page 215: 207
Username/Password - Type username and password for ACS Server for authentication. For example, if you want to use such CPE with VigorACS, you can type as the following: Username: acs Password: password Such information is useful for Auto Configuration CPE Settings Vigor2130 Series User’s Guide...
Page 216: System Password
Type in new password in this filed. New Password Type in the new password again. Confirm Password When you click OK, the login window will appear. Please use the new password to access into the web configurator again. Vigor2130 Series User’s Guide...
Page 217: User Password
Below shows an example for accessing into User Operation with User Password. 1. Type a new password in the field of New Password and click OK. 2. The following screen will appear. Simply click OK. 3. Log out Vigor2130 Web Configurator. Vigor2130 Series User’s Guide...
Page 218 Password and click Login. 5. The main screen with User Mode will be shown as follows. Settings to be configured in User Mode will be less than settings in Admin Mode. Vigor2130 Series User’s Guide...
Page 219: Configuration Backup
Click Backup button to get into the following dialog. Click Save button to open another dialog for saving configuration as a file. In Save As dialog, the default filename is config.cfg. You could give it another name by yourself. Vigor2130 Series User’s Guide...
Page 220 Click Restore button and wait for few seconds, the following picture will tell you that the restoration procedure is successful. Note: If the file you want to restore has been encrypted, you will be asked to type the encrypted key before clicking Restore. Vigor2130 Series User’s Guide...
Page 221: Syslog/Mail Alert
Assign a path for receiving the mail from outside. Mail From Type the user name for authentication. User Name Type the password for authentication. Password Check the box of User Login to send alert message to the Enable E-mail Alert Vigor2130 Series User’s Guide...
Page 222 Just set your monitor PC’s IP address in the field of Server IP Address. Install the Router Tools in the Utility within provided CD. After installation, click on the Router Tools>>Syslog from program menu. From the Syslog screen, select the router you want to monitor. Vigor2130 Series User’s Guide...
Page 223: Time And Date
Specify a time interval for the router to update current time. Automatically Update Interval Click the button to add a new NTP server. Add NTP server Click this button to remove an NTP server. Delete Click OK to save these settings. Vigor2130 Series User’s Guide...
Page 224: Management
A maximum of three IPs/subnet masks is allowed. List IP - Indicate an IP address allowed to login to the router. Subnet Mask - Represent a subnet mask allowed to login to the router. Vigor2130 Series User’s Guide...
Page 225: Reboot System
Note that this example is running over Windows OS (Operating System). Download the newest firmware from DrayTek's web site or FTP site. The DrayTek web site is www.draytek.com (or local DrayTek's web site) and FTP site is ftp.draytek.com.
Page 226: Diagnostics
Type in the payload size of the ICMP packet. Values range Ping Size from 8 bytes to 1400 bytes. Click this button to start the ping work. The result will be Start displayed on the screen. Vigor2130 Series User’s Guide...
Page 227: Trace Route
H - target is a host G - use gateway R - reinstate route for dynamic routing D - dynamically installed by daemon or redirect M - modified from routing daemon or redirect A - installed by addrconf Vigor2130 Series User’s Guide...
Page 228: System Log
Display the type or subsystem of the system log entry. Type You can specify the type from the drop down list to display the log just for the selected type. Vigor2130 Series User’s Guide...
Page 229: Traffic Overview
Display the number of received frames filtered by the Filtered forwarding process. Check it to enable auto-refresh function. Auto-refresh Click it to reload the page. Refresh Click it to clear the counters for all ports. Clear Vigor2130 Series User’s Guide...
Page 230: Detailed Statistics
RX 256-511 Bytes bad packets received. Display the number of 512 ~ 1023-byte frames in good and RX 512-1023 Bytes bad packets received. Display the number of 1024-1522-byte frames in good and RX 1024- 1526 Bytes Vigor2130 Series User’s Guide...
Page 231 Display the number of 1024 ~ 1522-byt frames in good and Tx 1024- 1526 Bytes bad packets transmitted. Display the number of 1527-byte frames in good and bad Tx 1527 Bytes: packets transmitted. Vigor2130 Series User’s Guide...
Page 232: Mac Address Table
When the end is reached the text "no more entries" is shown in the displayed table, use the l<< button to start over. Indicate whether the entry is a static or dynamic entry. Type Vigor2130 Series User’s Guide...
Page 233: Dhcp Table
It displays the MAC address for the specified PC that DHCP MAC Address assigned IP address for it. It displays the leased time of the specified PC. Expire Time Check it to enable auto-refresh function. Auto-refresh Click it to reload the page. Refresh Vigor2130 Series User’s Guide...
Page 234: Data Flow Monitor
Session web page. Block - can prevent specified PC accessing into Internet Action within 5 minutes. Unblock – the device with the IP address will be blocked in five minutes. The remaining time will be shown on the Vigor2130 Series User’s Guide...
Page 235: Sessions Table
You can check a range of certain devices by specifying the Source IP: Port / source and destination IP address (es) with the port number. Dest IP: Port Display the sessions based on the state chosen here. State Vigor2130 Series User’s Guide...
Page 236: Ports State
Check it to enable auto-refresh function. Auto-refresh Click it to reload the page if you change the LAN port Refresh connection. Or you can check Auto-refresh to reload the page by the system automatically. Vigor2130 Series User’s Guide...
Page 237: Trouble Shooting
Turn on the router. Make sure the ACT LED blink once per second and the correspondent LAN LED is bright. If not, it means that there is something wrong with the hardware status. Simply back to “1.3 Hardware Installation” to execute the hardware installation again. And then, try again. Vigor2130 Series User’s Guide...
Page 238 Go to Control Panel and then double-click on Network Connections. Right-click on Local Area Connection and click on Properties. Select Internet Protocol (TCP/IP) and then click Properties. Vigor2130 Series User’s Guide...
Page 239 Select Obtain an IP address automatically and Obtain DNS server address automatically. Double click on the current used Mac OS on the desktop. Open the Application folder and get into Network. On the Network screen, select Using DHCP from the drop down list of Configure IPv4. Vigor2130 Series User’s Guide...
Page 240: Pinging The Router From Your Computer
Open the Application folder and get into Utilities. Double click Terminal. The Terminal window will appear. Type ping 192.168.1.1 and press [Enter]. If the link is OK, the line of “64 bytes from 192.168.1.1: icmp_seq=0 ttl=255 time=xxxx ms” will appear. Vigor2130 Series User’s Guide...
Page 241: Checking If The Isp Settings Are Ok Or Not
Open WAN>>Internet Access page and then check whether the ISP settings are set correctly. Use the Connection Type drop down list to choose Static IP/DHCP/PPPoE/PPTP/L2TP/3G USB Modem for reviewing the settings that you configured previously. Vigor2130 Series User’s Guide...
Page 242: Forcing Vigor Router Into Tftp Mode For Performing The Firmware Upgrade
The .all firmware format will remain the former configurations after upgrading firmware. 10. Input the Password if you have set one, then click Send. 11. There is a bar showing the upgrading process. Vigor2130 Series User’s Guide...
Page 243 12. When the firmware upgrade is successful, the following window will pop up. Vigor2130 Series User’s Guide...
Page 244 Transfer Abort ! appears, please check if the firmware you download is correct for your Vigor router. Note: Please turn off the Firewall protection while upgrading the firmware with Windows Vista. The Firewall function can be turned off via Control Panel >> Security Center >> Firewall. Vigor2130 Series User’s Guide...
Page 245: Backing To Factory Default Setting If Necessary
5 seconds. When you see the ACT LED blinks rapidly, please release the button. Then, the router will restart with the default configuration. After restore the factory default setting, you can configure the settings for the router again to fit your personal request. Vigor2130 Series User’s Guide...
Page 246: Contacting Your Dealer
If the router still cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@draytek.com. Vigor2130 Series User’s Guide...

This manual is also suitable for:

Vigor2130n Vigor2130vn

Draytek Vigor2130 Series User Manual

Quick Links

Related Manuals for Draytek Vigor2130 Series

Summary of Contents for Draytek Vigor2130 Series

This manual is also suitable for:

Table of Contents