Operating Jvc's Audio/Video Components; Operating Audio Components - JVC RX-DP20VSL Instructions Manual

Operating JVC's Audio/Video Components

You can operate JVC's audio and video components with this receiver's remote control, since control signals for JVC
components are preset in the remote control.

Operating Audio Components

IMPORTANT:
To operate JVC's audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK (SYNCHRO) jacks (see page 55) in addition to the
connections using cables with RCA pin plugs (see pages 11
and 12).
• Aim the remote control directly at the remote sensor on the receiver.
• To operate a source with the remote control, the source must be
selected using source selecting buttons on the remote control.
• To operate the cassette deck or MD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 23.)
• Refer also to the manuals supplied with your components.
When using the remote control:
– Check the indication shown on the remote's display when you press
a button—this indicates the remote control operation mode for a
while.
– The CONTROL button can change the remote control operation
mode without changing the source.
Each time you press the button, the remote control operation mode
changes in the sequence—VCR1 = TAPE = CDR = CD DISC = (back
to the beginning).
LEARN
TRANSMIT
Ex. When you press FM/AM.
61
DVD AUDIO
LEARN
TRANSMIT
TV/DBS VCR 1
Tuner
You can always perform the following operations:
FM/AM
: Tunes in to the last station of the last
selected band. Each time you press the
button, the band alternates between FM
and AM (MW/LW).
After pressing FM/AM, you can perform the following operations:
1 – 10, +10 : Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then 10.
PTY SEARCH
: Searches for a program by PTY codes.
PTY +/– : Selects the PTY codes.
DISPLAY MODE : Shows the RDS signals.
TA/NEWS/INFO : Select the Enhanced Other Networks data
type (TA, NEWS, INFO)
FM MODE : Changes the FM reception mode.
Sound control section (Amplifier)
You can always perform the following operations:
THX : Selects the THX modes.
SURROUND
: Selects the Surround modes
EX/ES/7.1 : Selects the 7.1-channel reproduction
DSP : Selects the DSP modes.
SURR/DSP OFF
: Deactivates the THX/Surround/DSP
ANALOG DIRECT
: Turns on or off Analog Direct.
ANALOG/DIGITAL INPUT : Selects the analog/digital inputs.
CC CONVERTER
: Turns on or off CC Converter.
After pressing SOUND, you can perform the following operations:
TEST : Turns on or off the test tone output.
FRONT•L then LEVEL +/– : Adjusts the left front speaker
FRONT•R then LEVEL +/– : Adjusts the right front speaker
SUBWFR then LEVEL +/– : Adjusts the subwoofer output level.
CENTER then LEVEL +/– : Adjusts the center speaker channel
SURR•L then LEVEL +/– : Adjusts the left surround speaker
SURR•R then LEVEL +/– : Adjusts the right surround speaker
SURR BK•L then LEVEL +/– : Adjusts the left surround back
SURR BK•R then LEVEL +/– : Adjusts the right surround back
EFFECT : Selects the effect level.
LIVENESS : Selects the liveness.
Notes:
• After adjusting sounds, press the corresponding source selecting
button to operate your target source by using the 10 keys;
otherwise, the 10 keys cannot be used for operating your target
source.
• When you press LEVEL + or LEVEL –, the corresponding speaker
name appears on the remote's display.
modes.
modes.
channel output level.
channel output level.
output level.
channel output level.
channel output level.
speaker channel output level.
channel speaker output level.