Viewfinder Advanced Menu; Contents And Settings Of Each Page - Sony DSR-300 Service Manual

Viewfinder Advanced Menu

Move the POWER switch to
the ON position with the
MENU dial held down.
Turn the MENU dial.
Advanced
menu page 1
mPAGE1 (NEXTm$ PREVm4)
ALL RESET
(YESmPUSH)
EXIT MENU (YESmPUSH)
Align the cursor to
Confirmation "ALL RESET" and
screen press the MENU dial.
PAGE1 (NEXTm$ PREVm4)
Turn the MENU dial
mALL RESET SURE?
(to cancel resetting).
(YESmPUSH)
EXIT MENU (YESmPUSH)
Press the MENU dial
(to cancel resetting).
PAGE1 (NEXTm$ PREVm4)
mALL RESET OK!
(YESmPUSH) Turn the MENU dial.
EXIT MENU (YESmPUSH)
Turn the MENU dial. a)
a) Set the cursor to the page number (blinking) and turn the
MENU dial.
b) Set the cursor to EXIT MENU and press the MENU dial.
c) The menu configuration differs according to the connected
accessories such as remote control unit. (Some pages or
items may not displayed.)

Contents and Settings of Each Page

Each page's contents and settings are described below.
Advanced menu page 1
Use this page to return all menu settings to their
factory preset values.
84
Chapter 4 Viewfinder Screen Indications and Menus
Normal indications
T C G 1 2 : 3 4 5 6 : : 0 0
M
1 8 9
0
N D
9 8 0 4 0 1
S S : 1 / 0 0 1 0 1 0 : 0 0 M A
a)
page 2 c)
PAGE2 (NEXTm$ PREVm4)
Press the
GAIN
m HIGH:18dB b)
MENU dial.
MID : 9dB
LOW : OdB
DL:ON
EXIT MENU (YESmPUSH)
Turn the
MENU dial. a)
page 3 c)
PAGE3 (NEXTm$ PREVm4)
Press the
mAWB MEM : 2
MENU dial. b)
PRE. WHT : 3200
TONE : OFF
BARS : SMPTE
REMOTE1 : REC
REMOTE2 : MARK
BAUD RATE: 38400
EXIT MENU (YESmPUSH)
Turn the
MENU dial. a)
page 10 c)
mPAGE10(NEXTm$ PREVm4)
: ±0
SAT
: ±0
HUE
SKIN SAT: ±O
SKIN HUE: ±0
Press the
EXIT MENU (YESmPUSH)
b)
MENU dial.
For details of this operation, see "Advanced Menu
Operations" (page 83).
P A G E 1 ( N E X T m$ P R E V m4)
mALL RESET
( Y E S mPUSH)
E X I T M E N U ( Y E S mPUSH)
Advanced menu page 2
P A G E 2 ( N E X T m$ P R E V m4)
G A I N
m H I G H : 1 8 d B
M I D : 9 d B
L O W : O d B
D L : O N
E X I T M E N U ( Y E S mPUSH)
Item Settings
GAIN
This sets gain values for the positions of the GAIN switch.
The HIGH, MID, and LOW values must be set so that LOW
< MID < HIGH.
HIGH 3 dB, 6 dB, 9 dB, 12 dB, 18
Sets the H position. dB (normal value), 18 dB +
DPR, 24 dB, 24 dB + DPR,
HYPER GAIN
MID 0 dB, 3 dB, 6 dB, 9 dB
Sets the M position. (normal value), 12 dB, 18
dB, 18 dB + DPR, 24 dB, 24
dB + DPR
LOW –3 dB, 0 dB (normal
Sets the L position. value), 3 dB, 6 dB, 9 dB, 12
dB, 18 dB, 18 dB + DPR, 24
dB
DL ON (normal value), OFF
Sets DynaLatitude function When set to ON, the amount
ON/OFF. This setting is of DynaLatitude effects is
valid only when the set in basic menu page 2
(see page 79).
OUTPUT/DL/DCC+ switch
has been set to DL.
Advanced menu page 3
P A G E 3 ( N E X T m$ P R E V m4)
mA W B M E M : 2
P R E . W H T : 3 2 0 0
T O N E : O N
B A R S : S M P T E
R E M O T E 1 : R E C
R E M O T E 2 : M A R K
B A U D R A T E : 3 8 4 0 0
E X I T M E N U ( Y E S mPUSH)
a) For DSR-300P: EBU75
Item Settings
AWB MEM 2 (normal value): No
Selects whether or not to correspondence with FILTER
make the FILTER knob knob settings. Only two
settings (1 to 4) correspond adjustment values (A and B)
to separate white balance are stored in memory.
2 × 4FL: Correspondence
adjustment values stored in
memory. with FILTER knob settings.
Each of the four knob
settings can be used to set A
and B adjustment values, for
a total of eight settings.
PRE. WHT 3200 (normal value):
Selects the color 3200 K
temperature preset for the 3000: 3000 K
white balance adjustment.
TONE ON (normal value): Output
Selects whether or not to audio signal.
output a 1-kHz audio signal OFF: Do not output audio
with the color bars when the signal.
OUTPUT/DL/DCC+ has
been set to BARS.
BARS SMPTE (normal value for
Selects normal width or DSR-300): Normal width
narrower width for color EBU75 (normal value for
bars. DSR-300P): EBU 75%
EBU100 (for DSR-300P):
EBU 100%
SPLIT (for DSR-300P): Not
for normal operation
SNG: Narrower than normal
(used for satellite
communications, etc.)
REMOTE1 REC (normal value):
Sets a function for position 1 Specifies recording start/stop
of the RM-LG1 connected to MARK: Specifies a Mark IN/
the REMOTE connector 1. OUT point.
CUE: Specifies a Cue point.
NG: Specifies NG/OK.
REMOTE2 REC: Specifies recording
Sets a function for position 2 start/stop.
of the RM-LG1 connected to MARK (normal value):
the REMOTE connector 1. Specifies a Mark IN/OUT
point.
CUE: Specifies a Cue point
NG: Specifies NG/OK.
BAUD RATE 9600, 38400 (normal value)
Sets a baud rate for a
computer connected to the
REMOTE connector 1 (to be
supported in future version).
85
Chapter 4 Viewfinder Screen Indications and Menus