COMPONENTS IN THIS PACKAGE
HC-View-SS
Extension & Star Nut
(View & Wave only)
HC-Wave-SS
Washers
1-5/8"
1-5/8"
HC3-SS
Rubber
Small Steel
H-View-SS
Extension & Star Nut
H-Wave-SS
(View & Wave only)
GN3-SS
3/4" Screws (2)
3/4" Screws (2)
Semi-Circular
H990-SS
Mounting Plate
Fiber Gasket
Mounting Plate
H770-SS
4
3/8" Tube
Plug (1)
3/4" Screws (2)
Brass Nut / Ferrule /
Quick Connector
Wing Nut
2-1/4"
2-1/4"
Snap-Connect
Large Steel
Fiber
Fitting (3 pieces)
Washers
2-1/4"
1-5/8"
1-5/8"
Rubber
Small Steel
Large Steel
Snap-Connect
Wing Nut
Fitting (3 pieces)
Snap-Connect
Wing Nut
Rubber Gasket
Fitting (3 pieces)
3/4" Screws (2)
Metal
Snap-Connect
Mounting Screw
Fitting (3 pieces)
START HERE
1
PREPARATION
A
Required minimum from
center of hole to wall
HC-View-SS ...... 2
H-View-SS ........ 2
HC-Wave-SS .... 2
Tube Insert
H-Wave-SS ...... 2
HC3-SS ............ 2
GN3-SS ............ 2
H990-SS .......... 1
H770-SS .......... 2" ............................1"
HC3/GN3
*
The wall outlet for your dispenser must have power supplied to it continuously
Tank
and must be fused. It should not be controlled by the same wall switch
B
2-1/4"
Fiber
If you have to drill through sink or
countertop, you may need to rent or purchase
Tank
C
Tank
Consult a professional before drilling into
a surface other than stainless steel.
Tank
PROPER INSTALLATION SHOULD TAKE ABOUT 2-4 HOURS
■
Identify locations for the dispenser
Maximum counter
faucet, tank and filter (if applicable).
thickness (depth)
■
Check to make sure there is proper
5
⁄
" ..........................3"
8
clearance (see chart at left) for
5
⁄
" ..........................3"
8
dispenser handles to be fully opened.
5
⁄
" ..........................3"
8
3
⁄
"..........................3"
8
■
Check to make sure counter is not
1
⁄
" ..........................
3
⁄
" *
4
4
too thick (see chart at left).
1
⁄
" ..........................
3
⁄
" *
2
4
1
⁄
" ..........................3"
■
4
Make sure there is a grounded
electrical outlet under the sink.
, a
2" extension is available for oversized counters
that operates your disposer.
■
Turn off water supply.
■
If using the sink sprayer hose hole,
remove nut that connects sprayer
hose at bottom of faucet.
■
Using adjustable wrench, remove nut
connecting sprayer washer flange in
sprayer hole.
■
Plug hose opening with either a 1/8"
plug or a 1/4" cap (not supplied).
the appropriate tools.
What if you don't have a sprayer hole or
don't want to use it?
■
Many homeowners replace the soap
Required Hole Size
dispenser in their sink with an instant
1
⁄
" - 1
⁄
"
1
1
4
2
hot water dispenser.
■
If drilling a hole into a stainless steel
sink or counter top, you can cut a
mounting hole for the dispenser with a
hole saw for stainless steel, or you can
use a hole punch.
5