2
INSTALLING THE FAUCET - VIEW/ WAVE / HC3/ GN3
A
Property Damage: Do not pinch or break copper
tubing. Do not distort the last 1 inch of tubing.
B
1
5
⁄
" Small
8
Steel Washer
1
5
⁄
" Rubber
8
Washer
Cast Iron or
1
1
Hole larger than 1
⁄
" Hole
4
BOTH 1
5
⁄
" small steel and rubber washers
8
MUST BE INSTALLED to ensure
proper operation and seal.
C
Hot & Cool models only
An assistant may be needed to hold
the dispenser head in place
while securing the dispenser.
D
Fiber
Fiber
Washer
Wing Nut
Washer
Fig. 1
Fig. 2
Property Damage: Do not over tighten
the plastic wing nut
.
6
View/Wave/HC3/GN3
■
Unpack dispenser components.
■
On a firm, flat surface, carefully
straighten the copper tubing.
■
Remove the wing nut from
the valve body.
View/Wave/HC3/GN3
1
5
⁄
" Small
8
■
Steel Washer
For a 1
1
⁄
" sink hole, stack the
4
washers in this order on sink deck:
1
5
⁄
" Rubber
1) 1
5
⁄
" rubber washer
8
8
Washer
2) 1
⁄
" small steel washer.
5
8
2
1
⁄
" Large
4
Steel Washer
■
For a cast iron sink, or a hole larger
than 1
1
⁄
", stack the washers in this
4
1
⁄
"
4
order on sink deck:
1) 2
1
⁄
" large steel washer
4
2) 1
5
⁄
" rubber washer
8
3) 1
5
⁄
" small steel washer
8
View/Wave/HC3/GN3
■
Feed tubes down through the hole
in the sink or counter until the base
is at rest. Set faucet at desired angle.
Hot & Cool models only
■
Remove plug from the Y-shaped
quick-connector by depressing
release ring. Attach the quick
connector to the ends of the copper
tubes running from the dispenser.
■
Install a white 3/8" tube into
quick connector.
View/Wave/HC3/GN3
For counters less than 3/4 " thick (Fig. 1)
■
Slide 2
1
⁄
" fiber washer over faucet
4
threads under sink. Tighten assembly
using black plastic wing nut.
Star Nut
For counters more than 3/4 " thick (Fig. 2)
■
Thread extension (only included with
View/Wave) onto base of faucet
until tight. Slide 2
1
⁄
" fiber washer
4
over extension under sink. Tighten
assembly using plastic star nut.
2
INSTALLING THE FAUCET - H990
A
Property Damage: Do not pinch or break copper
tubing. Do not distort the last 1 inch of tubing.
B
Make sure to use rubber gasket
to ensure proper seal.
C
An assistant may be needed to hold
the dispenser head in place
while securing the dispenser.
H990
■
Unpack dispenser components.
■
On a firm, flat surface, carefully
straighten the copper tubing.
H990
■
Ensure that the black rubber gasket
is properly seated into the base of
the dispenser head and will
surround the sink mount.
■
Feed tubes down the hole in the
sink or countertop until the base is
at rest on the sink or countertop
surface.
H990
■
From under the sink, place the
semi-circular mounting plate onto the
threaded stud.
■
Place wing nut onto the threaded
stud. Make sure faucet head is at the
desired angle. Tighten the wing nut
until snug, while ensuring the semi-
circular mounting plate extends
beyond the sink hole.
7