Writing To Flash Memory (Ic8005); Writing To Mpeg Control (Ic8501) - Sony DCM-M1 Service Manual

2-2.

Writing to Flash Memory (IC8005)

Note 1: When the writing to the Flash Memory (IC8005) was
executed, perform the following:
• MAC Address Setting (See Test Mode page 16)
• Touch Panel Adjustment (See Test Mode page 20)
Note 2: Hyper Terminal setting must already be finished.
Note 3: on typical screen display indicates input characters.
1) Perform a setting to the set. (See page 25)
2) Make "Board Check Monitor ver1.XXX" displayed on the
screen, enter "WT" for the prompt and press the [Enter] key.
3) Data writing to the Flash Memory starts, and the progress sta-
tus is displayed on the screen as shown below. After about one
minute, [WT>OK] is displayed and the writing finishes.
Board Check Monitor ver1.XXX
> WT
Formatting FLASH file... src=1 ,dst=0
Format done.
Copying file: MDCX_ITRON
@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@
Copying file: MDCX_JAPP
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@
Copying file: MDCX_JAVA
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@
Copying file: MDCX_FTPBT
@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@
Copying file: MDCX_FTPD
@@@@@@@@
Copying file: MDCX_WKSCR
@@@@@
Copying file: MDCX_JDICS
@@@@@@@@@@@@@@@@
Copying file: MDCX_EFFECT
@
Copying file: MDCX_SLEEP
@
Copying file: MDCX_VERSION
@
Copying 2nd partition...
End of WT.
WT>OK
Fig.7-2-8 Typical screen display
4) Exit the Hyper Terminal. (See page 25)
2-3.

Writing to MPEG Control (IC8501)

Note 1: Hyper Terminal setting must already be finished.
Note 2: on typical screen display indicates input characters.
1) Insert MPEG RATE CONTROL disc into the drive A.
2) Perform a setting to the set. (See page 25)
3) Apply +15Vdc to the CN6 of Ether Flash BB.
4) Make "Board Check Monitor ver1.XXX" displayed on the
screen, enter "V" for the prompt and press the [Enter] key.
5) After [V850E>] is displayed, enter "R" and press the [Enter]
key.
6) Again, after [V850E>] is displayed, enter "L" and press the
[Enter] key.
7) From the Transfer on the menu bar, click [Send Text File] to
display the [Send Text File] screen.
Select [3 1/2 Floppy (A:)] for the Look in, and [All files (*.*)]
for the File type.
Click the "Rom_1000.hex" displayed on the screen to high-
light, and click [Open].
The data are then sent and displayed on the screen.
8) After [V850E>] is displayed, enter "A" and press the [Enter]
key.
The Flash Data writing starts, and the following is displayed:
[Program to V850 flash memory finished] Then, [V850E>] is
displayed as a prompt.
9) Enter "Q" to quit the data writing.
10) Exit the Hyper Terminal. (See page 25)
Note 3: Disconnect the +15Vdc applied to the CN6 of Ether Flash
BB in prior to disconnection of the power supply from
the AC Adaptor.
– 26 –
Fig. 7-2-9