JVC HM-HDS1U Instructions Manual page 17

ACCESS CABLE BOX
BRAND SET SCREEN
7
Press # (or 3) or OK.
ENTER CABLE BOX BRAND
8
Press the appropriate
NUMBER keys to enter
the Cable Box Code
from the CABLE BOX
BRAND LIST shown
below, then press # (or
3) or OK.
If the cable box's
channel changes to 9, setting is complete. Press # (or
3) or OK and "CABLE BOX CONTROL IS ON"
appears on the screen for about 5 seconds, then the
Initial Set Up screen appears. To returns to the normal
screen, press MENU.
If the cable box's channel does not change to 9, press
%fi (or 5∞) to select "NO", then press # (or 3) or
OK. By entering another code, repeat step 8 until the
cable box's channel changes to 9.
If the channel does not change after going through all
the code numbers listed for your model of cable box,
then try all the other numbers between 1 and 25.
CABLE BOX BRAND LIST
BRAND
ARCHER
CABLETENNA
CABLEVIEW
CITIZEN
CURTIS
DIAMOND
EASTERN
GC BRAND
GEMINI
GENERAL INSTRUMENTS
HAMLIN
JASCO
JERROLD
NOVAVISION
OAK
PANASONIC
PULSER
RCA
REGAL
REGENCY
REMBRANDT
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
SL MARX
SPRUCER
STARGATE
TELEVIEW
TOCOM
UNIKA
UNIVERSAL
VIDEOWAY
ZENITH
CABLE BOX BRAND SET
1
PRESS NUMBER KEY(0-9)
THEN(OK) TO TEST
PRESS(MENU) TO END
CODE
1, 5, 17
1, 17
15, 16, 17, 21, 25
15, 16, 17, 21, 25
2, 8
1, 17
19
15, 16, 17, 21, 25
15
1, 4, 6, 11, 12, 15
10, 18, 19, 23
15
1, 4, 6, 11, 12, 15
2, 8
7, 20
13, 14
15, 16, 17, 21, 25
13, 14
10, 18, 19, 23
19
1, 16, 17
5, 16, 24
2, 8
7, 20
5, 16, 17, 24, 25
13, 14
5, 15, 16, 17, 21, 24, 25
5, 16, 24
1, 4, 16
1, 17
16, 17, 25
3, 9, 22
3, 9, 22
INFORMATION
When the recorder's clock has not been set (with AUTO
CLOCK set to ON), if you press OK in step 7, "CABLE BOX
USERS SET CLOCK MANUALLY" will be displayed on the
screen for about 5 seconds, then the Clock Set screen will
appear; perform the manual clock setting procedure on
page 12. If you press MENU after the clock has been set,
the Cable Box Brand Set screen appears.
NOTES:
Although the supplied Controller is compatible with many
different cable box brands, it is possible that it will not work
with your cable box.
If your cable box doesn't respond to any code between 1 and
25, you can't use the Controller to change cable box
channels. In this case, make sure to leave the cable box
turned on and tuned to the proper channel before the
scheduled start of timer recording.
Please contact your cable company about the possibility of
exchanging your current cable box with one that is compatible
with your recorder.
The recorder can only change the cable box channel through
the Controller during timer recording.
If your cable box is one that can't be operated with a remote
control (because it has no remote sensor), you can't use the
Controller to change its channels. Make sure to leave the
cable box turned on and tuned to the proper channel before
the scheduled start of timer recording.
If the recorder's memory backup expires because of a power
failure, set the cable box output channel and brand again.
If you are unable to set the Controller, please contact JVC toll
free at 1-800-252-5722.
17
EN