Related Manuals for Benassi MC 3300
Summary of Contents for Benassi MC 3300
- Page 1 REVERSIBLE TWO-WHEEL TRACTOR MC 3300 MC 4300 SERIES Operation and Maintenance Manual...
-
Page 2: Table Of Contents
OPERATION AND MAINTENANCE MANUAL Contents General details _________________________________________________________________________________ 3 Introduction ____________________________________________________________________________________ 3 Information about the guarantee ____________________________________________________________________ 3 Training _______________________________________________________________________________________ 4 Key of symbols _________________________________________________________________________________ 4 Read immediately: ______________________________________________________________________________ 5 Operation _____________________________________________________________________________________ 5 Unsafe practice _________________________________________________________________________________ 5 Machine description _____________________________________________________________________________ 6 Specifications and performance ____________________________________________________________________ 6 Implements ____________________________________________________________________________________ 7 Remark on attaching implements _________________________________________________________________ 7... -
Page 3: General Details
OPERATION AND MAINTENANCE MANUAL General details Producing firm: BENASSI SpA Via Lampedusa, 1 Tel. 0039 051 820534 Fax 0039 051 6826164 e-mail: export@benassispa.it www.benassispa.it This manual has been written by the Industrial Engineer Mr CIAVAGLIA Sergio Global Service Italia Srl - 63029 Servigliano (ITALIA) -
Page 4: Training
NEVER ORANGE DANGER Benassi Spa, as the firm producing the REVERSIBLE TWO-WHEEL TRACTOR, disclaims any responsibility for any damage that can be ascribed to an improper use, to inattention or to the breach of safety regulations. It also disclaims any responsibility for any damage that may occur during the transport, unpacking and handling of the machine. -
Page 5: Read Immediately
OPERATION AND MAINTENANCE MANUAL Read immediately: BEFORE: WARNING HANDLING THE MACHINE; ⇒ USING THE MACHINE; ⇒ ADJUSTING; ⇒ CLEANING; ⇒ OPERATIONS OF MAINTENANCE ⇒ READ THE OPERATION MANUALS (MACHINE AND ENGINE) IF THE REVERSIBLE TWO-WHEEL TRACTOR IS USED IN A FIRM, WE REMIND YOU TO HAND IN A COPY OF THE MANUALS TO THE MAINTENANCE MANAGER. -
Page 6: Machine Description
OPERATION AND MAINTENANCE MANUAL Machine description The two-wheel tractor is build on a metal frame where the other parts are fixed: the engine, the gear, the axle and the steering handle, as you can see from the picture: Hand Clutch and motor-stop controls throttle control Gear levers control... -
Page 7: Implements
OPERATION AND MAINTENANCE MANUAL Implements The machine can be operated as well with the following implements: SICKLE BAR, PLOUGH, MOWER, SNOW THROWER, TRAILER, SHREDDER, REVERSIBLE PLOUGH, LEVELLING BLADE, ROTARY SWEEPER. For other implements, please get in touch with the producing firm. To attach and use the different implements, refer to the specific manual. -
Page 8: Description Of Controls
OPERATION AND MAINTENANCE MANUAL Description of controls Warning lights Ignition key (for those models who have it) Motor-stop lever Handle height adjustment lever Hand throttle control Clutch lever Button to lock clutch lever and motor-stop Button to lock lever differential lever Lever to lock differential Speed direction... -
Page 9: Version Of The Machine With Cutters
OPERATION AND MAINTENANCE MANUAL Version of the machine with cutters In this version the machine has cutters to till the soil. The external parts of the cutters and of the protective case can be disassembled, so you can vary the width of the machine. The widths you can obtain are as follows. -
Page 10: Reverse Of The Machine
OPERATION AND MAINTENANCE MANUAL Reverse of the machine In order to attach different implements, the machine can be reversed by turning the handle 180 degrees, as it is described in this page. DANGER OF During these operation: OPERATION TO PERFORM BRUISING AND WHEN THE MACHINE IS CRUSHING... -
Page 11: Positions And Controls Of Levers
OPERATION AND MAINTENANCE MANUAL Positions and controls of levers The position of motion lever and the effect obtained by using them depend on the configuration of the machine (normal or reversed). The pictures below show the two different situations. Power takeoff lever Power takeoff lever To engage power takeoff lever, engage clutch Power takeoff can be engaged only... -
Page 12: Adjustements
OPERATION AND MAINTENANCE MANUAL Adjustements The machine can be adjusted in some ways, which are shown as follows. OPERATION TO PERFORM DANGER OF During these operations: WHEN THE MACHINE IS BRUISING AND SWITCHED OFF CRUSHING You can adjust the height of the handle, in order to get a comfortable position, according to the features of the operator. -
Page 13: Picture 11 - Adjusting Wheels With Flange
OPERATION AND MAINTENANCE MANUAL In some versions of the machine, you can adjust the track of the wheels, for example to pass more easily through narrow places. DANGER OF ONLY TRAINED AND INFORMED STAFF SHOULD PERMORM THESE BRUISING AND OPERATIONS. TURN OFF THE MACHINE AND SET IT ON A FIRM OVERTURNING BEARING IN ORDER TO RAISE THE WHEELS FROM THE GROUND. -
Page 14: Starting The Machine
OPERATION AND MAINTENANCE MANUAL Starting the machine To start the machine, follow these instructions: BEFORE STARTING THE MACHINE, MAKE SURE THAT: - VENTILATION IS ENOUGH (YOU SHOULD GO OUTSIDE); DANGER OF - ALL THE CONTROL LEVERS ARE DISENGAGED; THE SPEED LEVER MUST BRUISING AND BE SET ON NEUTRAL POSITION (0);... -
Page 15: Operating The Machine
OPERATION AND MAINTENANCE MANUAL Operating the machine Once you have chosen one of the working configurations (normal or reversed) and made the adjustments you need (always respecting what is written in the relevant section of this manual), the machine is ready for use. -
Page 16: Switching The Machine Off
OPERATION AND MAINTENANCE MANUAL Switching the machine off When you want to switch the machine off, follow these instructions: Take the throttle control to the minimum of its stroke. Disengage the power takeoff and set the gear on neutral position. Loose the motor- stop lever: the machine will switch... -
Page 17: Residual Risk
OPERATION AND MAINTENANCE MANUAL Residual Risk The machine, even when you use caution, has some residual risks for the operator: DANGER OF THROWING MATERIALS AGAINST PERSONS, ANIMALS, OBJETS. RESPECT AND MAKE OTHERS RESPECT THE SAFETY DISTANCE DANGER: MOVING IMPLEMENTS DANGER OF BRUISING AGAINST THE IMPLEMENTS OF THE MACHINE THE CUTTERS CAN CAUSE INJURY TO HANDS WHEN THEY ARE WORKING OR DURING OPERATIONS OF MAINTENANCE MANUAL LOAD HANDLING WHILE (DIS)ASSEMBLING THE IMPLEMENTSO OF THE... -
Page 18: Maintenance
OPERATION AND MAINTENANCE MANUAL Maintenance General guidelines Warning: only trained and informed staff should perform the maintenance operations described in this manual. Warning: only the producing firm or the retailer of the machine should perform specific maintenance operations. While performing maintenance operations, the machine should be in a stable position. Never neglect maintenance: the life and the efficiency of the machine also depend on how it is maintained. -
Page 19: Gear: Changing The Oil
OPERATION AND MAINTENANCE MANUAL Gear: changing the oil The machine must be switched off and placed on a flat surface. After the first 50 working hours, change the gear oil. Then change it every 300 working hours. Empty the gear by taking off the plug shown in the picture. Collect the oil in a proper container. To fill up, put the plug in its place and tighten. -
Page 20: Cleaning
OPERATION AND MAINTENANCE MANUAL Cleaning General guidelines Cleaning is ordinary maintenance. With ordinary maintenance we mean scheduled operation of basic maintenance that do not generally require special qualifications, authorizations or tools. To clean the machine, switch it off, let it cool and place it in a stable position. Clean the machine: every day after every time you operate it. -
Page 21: Disassembly
OPERATION AND MAINTENANCE MANUAL Disassembly The machine is mainly made of iron materials (carrying structure, engine, frames, works, etc.), plastic and cables, etc., which do not need particular care for disposal. The gear and engine oil should be disposed of according to law. When disassembling, you should sort the plastic parts from the metallic ones for waste recycling, according to the law of the country where the machine is used. -
Page 22: Air Noise And Vibrations Produced By The Machine
OPERATION AND MAINTENANCE MANUAL Air noise and vibrations produced by the machine Equivalent continuous A- Sound power Accelerations on the handle grip EN weighted sound pressure level dB(A) 1033 – 28662/1 dB (A) Table 3 - Noise and vibrations In compliance with the legislative decree D.Lgs 277/91, fulfilling the 86/188 directive, the Employer provides to the measures against noise at the work place and to comply with the above law.