Panasonic KX-FLB852CX Service Manual page 85

6.2.3. SERVICE FUNCTION TABLE
Code Function
402 Mode setting of the network
501 Pause time set
507 V34 transmission start speed
508 V34 reception start speed
514 Bell signal detect time
520 CED frequency select
521 International mode select
522 Auto standby select
523 Receive equalizer select
524 Transmission equalizer select
529 Call Service Clear
550 Memory clear
551 ROM check
552 DTMF single tone test
553 Monitor on FAX communication
select
554 Modem test
555 Scan check
556 Motor test & H.V.P.S. check
557 LED test
558 LCD test
561 KEY test
563 CCD position adjustment setting
564 CCD auto adjustment
571 ITS auto redial time set
572 ITS auto redial line disconnection
time set
573 Remote turn-on ring number set
590 FAX auto redial time set
591 FAX auto redial time disconnection
time set
Set Value Effective
Range
1: Auto 1~5
2: Full duplex-
10Mbps
3: Full duplex-
100Mbps
4: Half duplex-
10Mbps
5: Half duplex-
100Mbps
X 100 msec 001~600
0: Disable 0~8
1: 33.6
2: 31.2
3: 28.8
4: 26.4
5: 24.0
6: 21.6
7: 19.2
8: 16.8
0: Disable 0~8
1: 33.6
2: 31.2
3: 28.8
4: 26.4
5: 24.0
6: 21.6
7: 19.2
8: 16.8
X 100msec 1~99
1:2100 Hz 1, 2
2:1100 Hz
1:ON 2:OFF 1, 2
1:ON 2:OFF 1, 2
1: 0 km 1~4
2: 1.8 km
3: 3.6 km
4: 7.2 km
1: 0 km 1~4
2: 1.8 km
3: 3.6 km
4: 7.2 km
1:ON 2:OFF 1, 2
1:OFF 1~3
2:PHASE B
3:ALL
(-3.75~+3.75 01~31
mm) 0.25 mm
unit
X number of 00~99
times
X second 001~999
X number of 01~99
rings
X number of 00~99
times
X second 001~999
85
Default Remarks
1 The unit has been set to "Automatic mode".
Nowadays most of routers and hubs are provided
with a function that connects the unit with
networks automatically. However, this setting is
available for such as an old-type hub that
supports only 10BASE-T. Accord the setting to the
connected hub and router.
030
1
1
06
1 See Symptom/Countermeasure Table for long
distance and international calls in (P.148).
1 See Symptom/Countermeasure Table for long
distance and international calls in (P.148).
1 The resolution reverts to the default when
transmission is complete.
1 Set RX equalizer to automatic mode.
1
Refer to Memory Clear Specification (P.87).
See (P.88).
2 See (P.88).
1 Sets whether to monitor the line signal with the
unit´s speaker during FAX communication or not.
See (P.88).
See (P.88).
0 See (P.88).
See (P.88).
See (P.88).
See (P.88).
16
05 Selects the number of times that ITS is redialed
(not including the first dial).
--- Sets the interval of ITS redialing.
10 Sets the number of rings before the unit starts to
operate TAM in the TEL mode.
05 Selects the number of redial times during FAX
communication (not including the first dial).
065 Sets the FAX redial interval during FAX
communication.
KX-FLB852CX / KX-FLB852CXS
----------
----------
----------
----------