Framing & Finishing; Final Finishing; Gas Specifications; Gas Inlet And Manifold Pressures - Majestic 360DVS2 Installation Instructions & Homeowner's Manual

Framing & Finishing
1. Choose the unit location.
2. Place the unit into position and secure it to the floor
with 1¹⁄₂" (38mm) screws or nails. Holes to secure
the unit to the floor are located behind the access
door grille on the left and right sides of the unit.
3. Frame in the fireplace with a header across the top.
It is important to allow for the finished wall face when
setting the depth of the frame.
4. Drywall (sheetrock) or wood material may be placed
with a zero clearance to the top edges of the appli-
ance when finishing walls above sides of the appli-
ance with glass windows. NOTE: Attach wall
finishing to constructed frame, not the appli-
ance.
5. On 360DVSL and 360DVSR, drywall, wood, or wood
molding may be placed with zero clearance to the
rear wall of the unit, along the vertical edge formed
by the standoffs, to intersection of the rear wall, to
the side wall having the small glass window. NOTE:
Attach wall finishing to constructed frame, not
the appliance.

Final Finishing

Noncombustible materials such as brick or tile may be
extended over the edges of the face of the appliance.
DO NOT cover any vent or grille panels.
If a Trim Kit is going to be installed on the fireplace, the
brick or tile will have to be installed flush with the edges
of the appliance.

Gas Specifications

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7
Model Fuel Gas Control
360DVS2RN Nat
360DVS2RP Prop
360DVS2EN Nat
360DVS2EP Prop
360DVS3RN Nat
360DVS3RP Prop
360DVS3EN Nat
360DVS3EP Prop
360DVSLRN Nat
360DVSLRP Prop
360DVSLEN Nat
360DVSLEP Prop
360DVSRRN Nat
360DVSRRP Prop
360DVSREN Nat
360DVSREP Prop
10006326
Max. Max.
Input Input
BTU/h BTU/h
Millivolt 38,000 26,600
Millivolt 38,000 28,500
24V Hi/Lo 38,000 26,600
24V Hi/Lo 38,000 28,500
Millivolt 38,000 26,600
Millivolt 38,000 28,500
24V Hi/Lo 38,000 26,600
24V Hi/Lo 38,000 28,500
Millivolt 38,000 26,600
Millivolt 38,000 28,500
24V Hi/Lo 38,000 26,600
24V Hi/Lo 38,000 28,500
Millivolt 38,000 26,600
Millivolt 38,000 28,500
24V Hi/Lo 38,000 26,600
24V Hi/Lo 38,000 28,500
360DVS Series Direct Vent Fireplaces
Gas Inlet & Manifold Pressures
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2
Inlet Minimum
Inlet Maximum
Manifold Pressure
Input ratings are shown in BTU per hour and are
certified without deration for elevations up to
4,500 feet (1,370 m) above sea level.
For elevations above 4,500 feet (1,370 m) in USA,
installations must be in accordance with the
current ANSI Z223.1/NFPA 54 and/or local codes
having jurisdiction.
In Canada, please consult provincial and/or local
authorities having jurisdiction for installations
above 4,500 feet (1,370 m).
360DVS2/ 360DVS3/ 360DVSL/ 360DVSR
CERTIFIED TO
ANSI Z21.88-2002/ CSA 2.33-2002
Vented Gas Fireplace Heaters

Gas Line Installation

When purging the gas lines, the window
frame assembly must be removed.
The gas pipeline can be brought in through the vent
end of the fireplace as well as the bottom. Knockouts
(to allow gas pipe installation and testing any gas
connection) are provided on the bottom behind the
valve. It is most convenient to bring the gas line in from
the vent end of the valve, as this allows fan installation
or removal without disconnecting the gas line.
The gas line connection can be made with properly
tinned 3/8" copper tubing, 3/8" rigid pipe, or an ap-
proved flex connector. Since some municipalities have
additional local codes, it is always best to consult your
local authority and the CSA-B149.1 installation codes.
For USA installations, consult the current National Fuel
Gas Code, ANSI Z223.1/NFPA 54.
Always check for gas leaks with a mild
soap and water solution. Do not use an
open flame for leak testing.
1/2" Gas Supply
Fig. 5 Gas shutoff valve and flex connector.
Natural LP (Propane)
4.5" w.c. 11.0" w.c.
14.0" w.c. 14.0" w.c.
3.5" w.c. 10.0" w.c.
1/2" NPT X 1/2" Flare Shut-Off Valve
3/8" Flex Line
(From Valve)
FP297a
9