Page 2
NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR office for information that is applicable and current.
Table of Contents Chapter 1: Installation Unpacking....................1-1 Viewing Angle Adjustment..............1-2 Detaching LCD Monitor from Its Stand ..........1-2 Interface for Arm Applications ............1-3 Connecting the Display to your Computer........1-4 Connecting the AC Power............. 1-5 Setting Up the LCD Monitor............1-5 Power Management System ..............
Preface This manual is designed to assist users in setting up and using the LCD Monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturers may void the user's authority to operate this equipment. Note: A shielded-type Video cord is required in order to meet the FCC emission limits and also to prevent interference to the radio and television reception.
Important Safety Instructions Please read the following instructions carefully. This manual should be retained for future use. To clean LCD Monitor screen; -- Power off LCD Monitor and unplug the AC Cord. -- Spray a non-solvent cleaning solution onto a rag. -- Gently clean the screen with dampened rag.
Installation Chapter 1: Unpacking Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses very little power, some ventilation is needed to ensure that the Monitor does not become too hot.
Chapter 1: Installation Viewing Angle Adjustment The LCD Monitor is designed to allow users to have a comfortable viewing angle. The viewing angle can be adjusted as follows: Top (-5°~ +30°). Figure 1-1 Warning Do not force the LCD Monitor over its maximum viewing angle settings as stated above.
Chapter 1: Installation Interface for Arm Applications Before installing to mounting device, please refer to Fig.1-2. The rear of this LCD display has four integrated 4 mm, 0.7 pitches threaded nuts, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-3.
Chapter 1: Installation Connecting the Display to your Computer Power off your computer. Connect one end of the signal cable to the LCD Monitor's VGA port. (See Fig. 1-4) 1. Connect the other end of the signal cable to the VGA port on your 2.
Chapter 1: Installation Connecting the AC Power Connect the power cord to the AC adapter. (See Fig. 1-5) Connect the AC adapter's DC output connector to the DC Power Jack of the monitor. Connect the power cord to an AC power source. Figure 1-5 Warning Please install a "Surge Protector"...
Chapter 1: Installation Dimensions 306 mm (12.0 in.) 304 mm (11.9 in.) 47 mm (1.9 in.) 133 mm 190 mm 13 mm (5.25 in.) (7.5 in.) (0.5 in.) 165 mm (6.5 in.) 19810...
Chapter 1: Installation NCR 7458 Integrated Mount This feature provides a display arm mount for integrating the 5942display on an NCR 7458 terminal. There are two versions of this feature. Kit No. Description 5942-F026 7458 Peripheral Tray Mount (Beige, G11)
Page 16
Chapter 1: Installation 2. Install the Display Arm onto the back of the Operator Display (4 screws). 20504a...
Page 17
3. Install the Left and Right Pivot Housings on the Display Arm. 20501 4. Install the display assembly in the terminal. See the NCR RealPOS Hardware User’s Guide (B005-0000-1440) for instruction how to complete this installation and where to connect the cables.
Display Controls Chapter 2: Displaying the On Screen Display (OSD) Menu The Control Keys are disabled at power up. To enable the keys: 1. Press and hold the Right-Arrow Key for 5 seconds. 2. Press and hold the Left-Arrow Key for 5 seconds. 3.
Chapter 2: Display Controls Adjusting the Monitor's Display The monitor has four function control buttons to select among functions shown on OSD menu, designed for easy user-viewing environments. 1. Use the Left- or Right-Arrow key to scroll to the Brightness function.
Chapter 2: Display Controls Function Description Icon Function Function Description BRIGHTNESS Bright ness range is 0 – 100. CONTRAST Contrast range is 0 – 128. H-POSITION Adjusts the display's horizontal position. V-POSITION Adjusts the display's vertical position. PHASE Focus and Clarity range is 0 – 31). Frequency-tracking feature for better stability and CLOCK clarity.
Chapter 2: Display Controls Color Temperature Settings Icon Function Description CIE coordinated Color Sets the CIE coordinate color 9300 Temperature of 9300°K temperature to 9300°K CIE coordinated Color Sets the CIE coordinate color 6500 Temperature of 6500°K temperature to 6500°K Three colors (Red, Green, Blue) Sets the settings to a by user can be adjusted from the OSD...
Technical Information Chapter 3: Specifications LCD Panel SANYO(TM121SV-02L11) SANYO(TM121SV-02L07) 12.1" (31 cm) 12.1" (31 cm) Size Active matrix color TFT Active matrix color TFT LCD Display Type 800 x 600 800 x 600 Resolution 800 x (RGB) x 600 800 x (RGB) x 600 Display Dot Display Area 246 x 184.5 (HxV)
Page 24
Chapter 3: Technical Information Video Input Impedance 75 Ohm ± 2% Polarity Positive Input Signal Analog RGB 0.7Vp-p Amplitude 0 - 0.7 ± 0.05 Vp Multi-mode Supported Horizontal Frequency: 24 ~ 48 KHz Vertical Frequency: 56 ~ 75 Hz Control Power On/Off switch with LED indicator Brightness...
Page 25
Chapter 3: Technical Information Power Management Mode Power Consumption* AC Input LED Color 20W maximum 240 VAC Green Standby 5W maximum 240 VAC Yellow Suspend 5W maximum 240 VAC Yellow 5W maximum 240 VAC Yellow DC Power Off 5W maximum 240 VAC Dark Yellow: Standby,...
Chapter 3: Technical Information Environment Operating: 5°C to 40°C/41°F to 104°F Temperature 20% to 80% Relative Humidity Storage: -20°C to 60° C/-4°F to140° F Temperature 5% to 85% Relative Humidity Power Supply (AC Adapter) Single phase, 100 ~ 240VAC, 50 / 60 Hz Input Voltage 0.8 A maximum Input Current...
Chapter 3: Technical Information Standard Timing Table If the selected timing is NOT included in table below, this LCD monitor will use the most suitable available timing. V. Freq. H/V Sync. Resolution H. Freq. (KHz) Pixel Freq. (MHz) Mode Polarity (Hz) 640 x 350 31.469...
Chapter 3: Technical Information Troubleshooting This LCD Monitor has pre-adjusted using factory standard VGA timings. Due to the output timing differences among various VGA cards in the market, users may initially experience an unstable or unclear display whenever a new display mode or new VGA card is selected.
Page 29
Chapter 3: Technical Information 2. Connect your PC system to another external CRT. If your PC system Functions properly with a CRT Monitor but it does not function with the LCD Monitor, the output timing of the VGA card may be out of the LCD’s synchronous range. Please change to an alternative mode listed in the Standard Timing Table or replace the VGA card, and then repeat steps 1.