Zenith H27H49S Installation Manual page 51

Installer Menu
Detailed Descriptions for Installer Menu Items 04 through 14
when some channels are not on nominal frequen-
cies. Note: BAND is automatically set by AUTO
PROGRAM. If some channels are not found by Auto
Prg. (Program), select the appropriate AFC setting
here and add the channels using the
ADD/DEL/BLNK option in the Setup Menu.
04. STRT CHANNEL (Start Channel)
When active, this function allows you to determine
the initial channel number when the TV is turned
On. This feature is useful for an in-house informa-
tion channel, since the TV would always select
that channel when it is turned On. Setting this to
255 causes the last channel viewed when the TV is
turned Off, to be the tuned to channel when the
TV is turned On again. The range of values is 0 -
255. Use ADJ (adjust) keys to choose numbers for
the start channel. Note: If set to '0', tunes to Aux
source selected at TV power On, see item 046.
05. CHAN LOCK (Channel Lock)
CHAN LOCK is ideal if a cable box (or similar) is
the sole source for programming—and the TV must
always be on the same channel. Changing channels
with Channel Up/Down or keypad numbers is
impossible. Channel Lock is inactive when set to 0
(default). Generally, this feature is used in con-
junction with START CHANNEL (item 04-I.) where
the start channel may, for example, be set to 3 or
4. If the start channel is 3, then the TV will
remain on channel 3. Note: If CHANNEL LOCK is
active and CHANNEL OVER RIDE is disabled, AUTO
PRG. (Program) is not functional.
06. GHOST CH. (Ghost Channel)
If set to 1, the current channel number is dis-
played in the upper right corner of the picture. The
number moves slightly to prevent damage to the
screen. The default is "0" or Off. Note: If captions
are On, "Ghost Channel" is not displayed.
07. START VOLUME
This function allows the Installer to determine the
initial volume level setting when the TV is turned
On. This feature is useful for an in-house informa-
tion channel, since the TV would always select
that Volume level when it is turned on. The range
of values are 0 - 63, 255. If 255 is selected, the
current volume level will be retained in memory
when the TV is turned Off. At TV turn On, Volume
level is automatically set to the previous level.
08. MIN VOLUME (Minimum Volume)
This function determines the minimum volume
level allowable with the VOLUME (VOL) Up/Down
control. In this way, for example, someone cannot
set the sound too low to hear. The range is from 0
to 63 change values with ADJ (Adjust) Left/Right
keys. The factory default is 0, which provides full
range of volume control. It may be best to set the
same value on every TV.
Note: The minimum volume level cannot have a
value setting higher than in the MAX VOLUME level
(described below).
09. MAX VOLUME (Maximum Volume)
This function determines the maximum volume
level allowable with the Volume Up/Down control.
In this way, for example, someone cannot set the
sound level high enough to disturb others. The
range is 0 to 63, with 63 as the default which
gives the user the full range of volume control.
Change values with Left/Right arrow keys. It may
be best to set the same value on every TV.
Note: The maximum volume level cannot have a
value setting lower than the MIN VOLUME level
(See Item 008).
10. MUTE DISABLE
Enables or disables sound mute function.
If set to 1, sound cannot be muted.
If set to 0, sound can be muted.
11. KEY DEFEAT
Enables/disables MENU, Up / Down / Left / Right
arrow keys on the front control panel. Set to 0 to
enable, set to 1 to disable.
12. NOT USED
13. NOT USED.
14. NOT USED
Page 51