Fisher & Paykel CG302D Installation Instructions Manual
Gas-on-glass cooktop
Hide thumbs
Also See for CG302D:
- User manual (24 pages) ,
- Installation instructions manual (21 pages) ,
- Installation manual (32 pages)
Related Manuals for Fisher & Paykel CG302D
Summary of Contents for Fisher & Paykel CG302D
-
Page 1: Installation Instructions
INSTALLATION INSTRUCTIONS Gas-on-glass cooktop CG302D, CG451D, CG603D, CG604D, CG752D, CG903D & CG905D models NZ AU 590149D 02.13... -
Page 2: Safety And Warnings
SAFETY AND WARNINGS Do not use or store flammable materials on or near this appliance. WARNING! Do not spray aerosols in the vicinity of this appliance while it is in operation. Electrical shock hazard Packing elements (eg plastic bags, polystyrene foam, staples, packing straps etc) and tools should not be left around during and after installation, especially if they are within easy reach of children, as these Before carrying out any work on the electrical section of the appliance, it must may cause serious injuries. -
Page 3: Parts Supplied
PARTS SUPPLIED 1 / 2 Dual Wok Pan support Pan support Small pan support (1) Wok stand (1) Fibre washer (1) Elbow “ BSP Mini wok Pan (Models with a Dual Wok only) (not supplied with support (1) (some models only) external thread (1) (CG604D only) Dual Wok only models) - Page 4 GAS RATE SUMMARY-MODELS SEMI-RAPID SEMI-RAPID DUAL WOK DUAL WOK SEMI-RAPID CG302D CG451D CG603D SEMI-RAPID SEMI-RAPID DUAL WOK DUAL WOK MINI WOK CG604D CG752D SEMI-RAPID SEMI-RAPID DUAL WOK SEMI-RAPID DUAL WOK DUAL WOK RAPID CG903D CG905D...
-
Page 5: Gas Rate Summary
GAS RATE SUMMARY All appliances are factory set for Natural gas or LPG and are not convertible. Check the appliance data label. CG302D CG451D CG603D BURNER SEMI-RAPID DUAL WOK SEMI-RAPID DUAL WOK Nominal Nominal Nominal Nominal Nominal Jet size Jet size... - Page 6 PRODUCT & CABINETRY DIMENSIONS Note: Gas inlet connection is located in the rear right corner. FRONT REAR SIDE Product and cabinetry dimensions (mm) overall height of product (excluding burners, dials and pan supports) overall width of product overall depth of product height of chassis (below top of bench) width of chassis...
-
Page 7: Clearance Dimensions
CLEARANCE DIMENSIONS FRONT Clearance dimensions (mm) minimum clearance from left edge of cutout to nearest combustible surface minimum clearance from right edge of cutout to nearest combustible surface minimum clearance from rear edge of cutout to: nearest combustible surface nearest non-combustible surface minimum height of non-combustible material when used on adjacent walls minimum clearance from glass surface to: rangehood... - Page 8 FLUSH MOUNTING INSTALLATION (NOT RECOMMENDED) WARNING! We do not recommend flush mounting and sealing as servicing requires the cooktop to be removed from the benchtop. The owner carries all risk for flush mounting the cooktop. The owner must ensure the cooktop has been cut out from the benchtop before servicing can be carried out.
- Page 9 FLUSH MOUNTING INSTALLATION (NOT RECOMMENDED) ROUTER THE BENCHTOP TO THE FIT THE CLAMPING BRACKETS MASK OFF THE AREA TO BE SPECIFIED DEPTH SILICONED view from below Choose most appropriate slot for benchtop 5 mm 16 - 50mm APPLY SILICONE WIPE OFF EXCESS SILICONE IF REMOVING PRODUCT, CUT AROUND THE SILICONE TO REMOVE PRODUCT...
- Page 10 DISCARD PACKAGING REMOVE THE TWO TRANSIT SCREWS Recycle responsibly Repeat on the other side FIT THE ELBOW AND WASHER LOWER GENTLY INTO THE CUTOUT Fibre washer Elbow (1/2” BSP external thread) Floating nut...
- Page 11 FIT CLAMPING BRACKETS BASED ON THE SECURE TO BENCHTOP BENCHTOP THICKNESS view from below 16-20mm 20-30mm 30-40mm 40mm+ Repeat on all the other sides CONNECT TO GAS SUPPLY CHECK ALL CONNECTIONS FOR GAS LEAKS NG Models LPG Models Make sure to fit the supplied Make sure to fit the supplied regulator.
-
Page 12: Test Operation
AFFIX DUPLICATE DATA LABEL SOMEWHERE FIT PAN SUPPORTS ACCESSIBLE & PLUG COOKTOP IN Ensure the pan supports are located securely and in the correct orientation (refer to User guide) Duplicate data label TEST OPERATION To check that the ignition system operates correctly, light each burner by itself, then all burners in combination. -
Page 13: Final Checklist
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Installer’ s name: Have you installed the clamping brackets? Installer’ s signature: Have you verified that the type of model (factory-set for NG or LPG) Installation company: matches the type of gas at the site of installation? Date of installation: Have you used the fibre washer supplied? Have you leak-tested all connections?