Fisher & Paykel CG302D Installation Instructions Manual
Gas-on-glass cooktop
Hide thumbs
Also See for CG302D:
- User manual (24 pages) ,
- Installation instructions manual (17 pages) ,
- Installation manual (32 pages)
Related Manuals for Fisher & Paykel CG302D
Summary of Contents for Fisher & Paykel CG302D
-
Page 1: Installation Instructions
INSTALLATION INSTRUCTIONS Gas-on-glass cooktop CG302D, CG451D, CG603D, CG604D, CG752D, CG903D & CG905D models GB IE IN 590657A 02.14... -
Page 3: Safety And Warnings
SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS! WARNING! Particular attention shall be given to the relevant Electrical shock hazard requirements regarding ventilation. Read these instructions carefully before installing Before carrying out any work on the this product. electrical section of the appliance, it Please make this information available to the must be disconnected from the mains person installing the appliance as it could reduce... - Page 4 SAFETY AND WARNINGS Important! Do not use or store flammable materials on or Regardless of room size, all rooms containing the near this appliance. appliance must have direct access to the outside air Do not spray aerosols in the vicinity of this via an openable window or equivalent.
- Page 5 SAFETY AND WARNINGS the supply connection point (gas shut-off valve) is Before you install the appliance, please make accessible after installation. sure that the local distribution conditions (nature of the benchtop is made of a heat resistant material. gas and pressure) and the adjustment of the the installation complies with all the requirements appliance are compatible.
- Page 6 SAFETY AND WARNINGS When you install the appliance If, after following the instructions given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel Authorised Service Centre, Customer Care, or contact us through our website listed at the end of this document.
-
Page 7: Parts Supplied
PARTS SUPPLIED 1 / 2 Dual Wok Pan support Pan support Small pan support (1) Wok stand (1) Fibre washer (1) Elbow “ BSP Mini wok Pan (Models with a Dual Wok only) (not supplied with support (1) (some models only) external thread (1) (CG604D only) Dual Wok only models) - Page 8 GAS RATE SUMMARY-MODELS SEMI-RAPID SEMI-RAPID DUAL WOK DUAL WOK SEMI-RAPID CG302D CG451D CG603D SEMI-RAPID SEMI-RAPID DUAL WOK DUAL WOK MINI WOK CG604D CG752D SEMI-RAPID SEMI-RAPID DUAL WOK SEMI-RAPID DUAL WOK DUAL WOK RAPID CG903D CG905D...
-
Page 9: Gas Rate Summary
GAS RATE SUMMARY All appliances are factory set for Natural gas or LPG and are not convertible. Check the appliance data label. CG302D, CG451D, CG603D, CG604D, CG752, CG903 & CG905 BURNER SEMI-RAPID RAPID MINI WOK DUAL WOK Nominal Nominal Nominal... - Page 10 PRODUCT & CABINETRY DIMENSIONS Note: Gas inlet connection is located in the rear right corner. FRONT REAR SIDE Product and cabinetry dimensions (mm) overall height of product (excluding burners, dials and pan supports) overall width of product overall depth of product height of chassis (below top of bench) width of chassis...
-
Page 11: Clearance Dimensions
CLEARANCE DIMENSIONS FRONT Clearance dimensions (mm) minimum clearance from left edge of cutout to nearest combustible surface minimum clearance from right edge of cutout to nearest combustible surface minimum clearance from rear edge of cutout to: nearest combustible surface nearest non-combustible surface minimum height of non-combustible material when used on adjacent walls minimum clearance from glass surface to: rangehood... - Page 12 FLUSH MOUNTING INSTALLATION (NOT RECOMMENDED) WARNING! We do not recommend flush mounting and sealing as servicing requires the cooktop to be removed from the benchtop. The owner carries all risk for flush mounting the cooktop. The owner must ensure the cooktop has been cut out from the benchtop before servicing can be carried out.
- Page 13 FLUSH MOUNTING INSTALLATION (NOT RECOMMENDED) ROUTER THE BENCHTOP TO THE FIT THE CLAMPING BRACKETS MASK OFF THE AREA TO BE SPECIFIED DEPTH SILICONED view from below Choose most appropriate slot for benchtop 5 mm 16 - 50mm APPLY SILICONE WIPE OFF EXCESS SILICONE IF REMOVING PRODUCT, CUT AROUND THE SILICONE TO REMOVE PRODUCT...
- Page 14 DISCARD PACKAGING REMOVE THE TWO TRANSIT SCREWS Recycle responsibly Repeat on the other side FIT THE ELBOW AND WASHER LOWER GENTLY INTO THE CUTOUT Fibre washer Elbow (1/2” BSP external thread) Floating nut...
- Page 15 FIT CLAMPING BRACKETS BASED ON THE SECURE TO BENCHTOP BENCHTOP THICKNESS view from below 16-20mm 20-30mm 30-40mm 40mm+ Repeat on all the other sides CONNECT TO GAS SUPPLY CHECK ALL CONNECTIONS FOR GAS LEAKS NG Models LPG Models Make sure to fit the supplied Adjust to obtain a test point test point adaptor.
-
Page 16: Test Operation
AFFIX DUPLICATE DATA LABEL SOMEWHERE FIT PAN SUPPORTS ACCESSIBLE & PLUG COOKTOP IN Ensure the pan supports are located securely and in the correct orientation (refer to User guide) Duplicate data label TEST OPERATION To check that the ignition system operates correctly, light each burner by itself, then all burners in combination. -
Page 17: Final Checklist
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Installer’ s name: Have you installed the clamping brackets? Installer’ s signature: Have you verified that the type of model (factory-set for NG or LPG) Installation company: matches the type of gas at the site of installation? Date of installation: Have you used the fibre washer supplied? Have you leak-tested all connections?