Warranty; Product Reference Information; Wiring Diagrams - Superior SSDVST-CNM-B Care And Operation Instructions Manual

WARRANTY

Your gas appliance is covered by a limited twenty
year warranty. You will find a copy of the war-
ranty accompanying this manual. Please read
the warranty to be familiar with its coverage.
Retain this manual. File it with your other docu-
ments for future reference.
REPLACEMENT PARTS
A complete parts list is found at the end of
this manual. Use only parts supplied from the
manufacturer.
With proper care and maintenance, your appli-
ance will provide many years of enjoyment. If
you should experience any problem, first refer
to the troubleshooting guide in this manual.
If problem persists, contact your LHP dealer
or distributor.

WIRING DIAGRAMS

Wiring diagrams are provided here for reference
purposes only. This information is also provided
on schematics attached directly to the appliance
on a pullout panel located within the control
compartment.
Millivolt Wiring Diagram
If any of the original wire as
Schematic Repre-
supplied must be replaced,
sentation Only
it must be replaced with
Type AWM105 o C - 18
gage wire.
Thermopile
Standard OFF/ON Switch
*Optional Switch
* Optional Kits Installed - OFF/ON wall switch, wall
thermostat or remote control receiver. Note: Turn the
appliance-mounted OFF/ON burner control switch to the
OFF position if any of these kits are installed.
Figure 14
Normally, all parts should be ordered through
your LHP distributor or dealer. Parts will be
shipped at prevailing prices at time of order.
When ordering repair parts, always give the
following information:
1. The model number of the appliance.
2. The serial number of the appliance.
3. The part number.
. The description of the part.
5. The quantity required.
6. The installation date of the appliance.
If you encounter any problems or have any
questions concerning the installation or ap-
plication of this system, please contact your
dealer or distributor.
Your Fireplace's Model Number ___________________________________________
Your Fireplace's Serial Number ___________________________________________
The Date On Which Your Fireplace Was Installed ______________________________
The Type of Gas Your Fireplace Uses _______________________________________
Your Dealer's Name ___________________________________________________
CAUTION: LABEL ALL WIRES
PRIOR TO DISCONNECTION WHEN
SERVICING CONTROLS. WIRING
ERRORS CAN CAUSE IMPROPER
AND DANGEROUS APPLIANCE
OPERATION.
View A
J-Box Wiring when
using unit mounted
relay module.
Junction Box
Pilot Burner
Assembly
Field Wired
Factory
Wired
BL
BL
BK
BK = BLACK BL = BLUE
R = RED W = WHITE
G = GREEN
Optional Control Switch
Figure 15
Relay Module C/W FBK-250 only. Plug blower
into J-Box receptacle for FBK-100 or FBK-200
application. See View A for J-Box wiring.
BK
W
G
Optional Blower
*OFF/ON Switch
(Integral with
Gas Valve)
Honeywell
Electronic
Gas
Valve
Igniter
Connector
Transformer
BL
R
24 V
Secondary
BK
BK
W
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
LHP
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
visit us at www.Lennox.com
1-800-9-LENNOX

PRODUCT REFERENCE INFORMATION

We recommend that you record the following
important information about your fireplace.
Please call LHP for the phone number of your
nearest LHP dealer who will answer your ques-
tions or address your concerns.
ATTENTION : AU MOMENT DE
L'ENTRETIEN DES COMMANDES,
ÉTIQUETEZ TOUS LES FILS AVANT
DE LES DÉBRANCHER. DES
ERREURS DE CÁBLAGE PEU-VENT
ENTRAÎNER UN FONCTIONNEMENT
INADÉQUAT ET DANGEREUX.
Electronic Wiring Diagram
(Honeywell) Showing Blower
Wiring for Optional FBK-100, FBK-
200 & FBK-250 Kits
* Leave the OFF/ON switch, which is
integral with the gas valve, in the ON
position.
**Optional Control Switches: Wall
Switch, Wall Thermostat or Remote
Control Receiver.
GROUND
Notes:
1. If any of the original wire as supplied
must be replaced, use Type AWM 105°C
120 VAC
- 18 gage wire ONLY.
Primary
2. 120 VAC, 60 Hz - Less than 3 Amps.
Caution: label all wires prior to
disconnection when servicing controls.
Wiring errors can cause improper and
Field Wired
dangerous operation.
Factory
Schematic Representation Only
Wired
13