Using The Shower; Grey Water System; Shore Water Connection - Four winns 248 Vista Owner's Manual

D. Using The Shower
Turn on the faucets to desired temperature, remove the
shower spout from the sink faucet receptacle, press the
lever on the shower head, and the shower is operational.
The shower hose is connected to the shower spout and
runs inside the faucet receptacle and underneath the sink.
Certain models have a wall mount shower bracket for
convenience.
When using the shower, draw the shower curtain before
using the shower. Damage to the finish can result if sur-
rounding walls and flooring are allowed to become exces-
sively wet. Thoroughly dry these areas after showering.
The water temperature can vary during shower
use as the pressure pump cycles on and off. For
greatest consistency, turn the cold water on full,
then mix in hot water until the desired tempera-
ture is obtained.
A shower sump pump is incorporated into the drain sys-
tem of the shower. The shower drains into the sump pump
located forward of the aft cabin. The water will then be
pumped into the black/grey water holding tank . If a grey
water system is installed, the water will be pumped into
the grey water holding tank.
The sump pump includes an automatic bilge switch and
is protected by a circuit breaker either at the AC/DC cabin
panel, helm fuse block or the battery switch (FORWARD
or AUTO BILGE) depending on the model. The sump
pump will automatically start as soon as the water in the
sump reaches a level that will cause the float on the switch
to rise.
After showering, let the water flow for a period of time to
flush the pump of soap residue. Check the sump for ex-
cess residue. When rinsed out, the pump will automati-
cally shut off.
If water flow from the shower head appears to be restrict-
ed, it may be due to sediment accumulating at the shower
head. If necessary, remove the head and clean the dis-
charge holes with a fine wire.
Periodically check the sump pump screen for clogs to
prevent drainage problems from occurring in the shower
drain. Refer to the manufacturer's literature included in
the owner's packet.
Vista Owner's Manual
™
J - 3

GREY WATER SYSTEM

The grey water system is optional on Vista™ models.
The water from the galley sink, head sink and shower
will drain into a sump and is pumped into a grey water
holding tank respectively. The waste level indicator is
located in the head compartment. A pumpout fitting
labeled WASTE but designated for grey water is pro-
vided on the deck. Refer to the drawings at the end of
this section.
NOTICE
Certain geographical areas have restrictions on
grey water being pumped or drained overboard.
Be sure to check all local, state and federal laws
in the boating area.
J - 4

SHORE WATER CONNECTION

Shore water connection is standard on all Vista™ mod-
els. This feature allows the direct connection of a city or
shoreside water supply to the boat's water system to
provide a constant supply of fresh water without the need
to constantly refill the water supply tank. This minimizes
pressure pump operation thus extending the life span of
the pump.
Dockside shore water pressure can vary dramatically.
Excess pressure could damage the boat's water sys-
tem so the shore connection also regulates the water
pressure to a maximum of 35 psi.
The female inlet deck fitting may in the transom door
storage area or starboard side of the transom above the
swim platform.
To use shore water, connect a hose from the shore water
faucet to the shore water fitting on the boat and turn on
the shore water. The water system of the boat will then
be pressurized by city water if the system was previ-
ously primed.
The water pump should be turned off when using city
water. City water pressure varies from area to area. If
the pump is ON and water pressure drops below 35 psi,
the pump will activate to maintain pressure at 35 psi. It
will draw water out of tank and bypass city water.
If the pump is OFF, the pump will not function and the
water in the storage tank of the boat will not be utilized.
Section J
Page 4