Related Manuals for Planet WGSW-48040HP
Summary of Contents for Planet WGSW-48040HP
- Page 1 48-Port 10/100/1000Mbps 802.3at PoE Managed Switch with 4 Shared SFP Ports WGSW-48040HP Quick Installation Guide...
-
Page 2: Table Of Contents
Table of Contents 1. Package Contents ..................3 2. Requirements ..................... 4 3. Terminal Setup ................... 5 4. Logon to the Console .................. 6 5. Configuring IP Address ................7 6. Starting Web Management .................10 7. Saving Configuration ..................13 8. Recovering Back to Default Configuration .............14 9. Customer Support ..................15... -
Page 3: Package Contents
1. Package Contents Thank you for purchasing PLANET 48-Port 10/100/1000Mbps 802.3at PoE Managed Switch with 4 shared SFP ports, WGSW-48040HP. “Managed Switch” mentioned in this Guide refers to the WGSW-48040HP. Open the box of the Managed Switch and carefully unpack it. The box should contain the following items: The WGSW-48040HP Managed Switch x 1 User’s Manual CD x 1... -
Page 4: Requirements
2. Requirements Workstations running Windows XP/2003/Vista/7/8/2008, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/IP protocols. Workstations are installed with Ethernet NIC (Network Interface Card) Serial Port Connection (Terminal) The above Workstations come with COM Port (DB9) or USB-to-RS-232 converter. The above Workstations have been installed with terminal emulator, such as Hyper Terminal included in Windows XP/2003. -
Page 5: Terminal Setup
3. Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to RJ-45 type of serial (console) port of the Managed Switch. Console PC / Workstation with Managed Switch Terminal Emulation Software 115200,N,8,1 Serial Port RJ-45 DB9 RS-232 Cable RJ-45 Type Serial Port 115200,N,8,1 Figure 3-1 Managed Switch Console Connectivity A terminal program is required to make the software connection to the Managed Switch. Windows’ Hyper Terminal program may be a good choice. The Hyper Terminal can be accessed from the Start menu. -
Page 6: Logon To The Console
4. Logon to the Console Once the terminal is connected to the device, power on the Managed Switch, and the terminal will display “running testing procedures”. Then, the following message asks to log-in user name and password. The factory default user name and password are shown as follows and the login screen in Figure 4-1 appears. -
Page 7: Configuring Ip Address
5. Configuring IP Address The Managed Switch is shipped with default IP address shown below. IP Address: 192.168.0.100 Subnet Mask: 255.255.255.0 To check the current IP address or modify a new IP address for the Switch, please use the procedures as follows: Show the current IP Address 1. At the “#” prompt, enter “show ip interface brief”. 2. The screen displays the current IP address as shown in Figure 5-1. Figure 5-1: IP Information Screen... - Page 8 Configuring IP Address 3. At the “#” prompt, enter the following command and press <Enter> as shown in Figure 5-2. # configure terminal (config)# interface vlan 1 (config-if-vlan)# ip address 192.168.1.100 255.255.255.0 The previous command would apply the following settings for the Managed Switch. IP Address: 192.168.1.100 Subnet Mask: 255.255.255.0 Figure 5-2: Configuring IP Address Screen 4. Repeat step 1 to check if the IP address is changed.
- Page 9 Store current switch configuration 5. At the “#” prompt, enter the following command and press <Enter>. # copy running-config startup-config Figure 5-3: Saving Current Configuration Command Screen If the IP is successfully configured, the Managed Switch will apply the new IP address setting immediately. You can access the Web interface of the Managed Switch through the new IP address.
-
Page 10: Starting Web Management
6. Starting Web Management The following shows how to start up the Web Management of the Managed Switch. Note the Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set on the same IP subnet address. For example, the default IP address of the Managed Switch is 192.168.0.100, then the manager PC should be set at 192.168.0.x (where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0. - Page 11 2. When the following dialog box appears, please enter the default user name and password “admin” (or the password you have changed via console). The login screen in Figure 6-2 appears. Default Username: admin Default Password: admin Figure 6-2: Login Screen 3. After entering the password, the main screen appears as Figure 6-3 shows. Figure 6-3: Web Main Screen of Managed Switch...
- Page 12 The Switch Menu on the left of the Web page let you access all the commands and statistics the Managed Switch provides. Figure 6-4: Switch Menu If you are not familiar with Switch functions or the related parameter, press “Help icon” anytime on the Web page to get the help description. Note Now, you can use the Web management interface to continue the Switch management or manage the Switch by console interface.
-
Page 13: Saving Configuration
7. Saving Configuration In the Managed Switch, the running configuration file stores in the RAM. In the current version, the running configuration sequence of running-config can be saved from the RAM to FLASH by executing save startup config command, so that the running configuration sequence becomes the startup configuration file, which is called configuration save. -
Page 14: Recovering Back To Default Configuration
10 seconds. After the device is rebooted, you can login the management WEB interface within the same subnet of 192.168.0.xx. Fiber FAN Alarm 2 FAN Alarm 1 RESET Figure 8-1: WGSW-48040HP Reset Button... -
Page 15: Customer Support
9. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team. PLANET online FAQ : http://www.planet.com.tw/en/support/faq.php?type=1 Switch support team mail address : support_switch@planet.com.tw Copyright © PLANET Technology Corp. 2014. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. - Page 16 This page is intentionally left blank...