Honda Magna VF750C Service Manual page 15

General Information
Clutch lever free play
Cl utch outer guide I . D .
Clutch spring free length
Clutch disc thickness A
B (Judder spring side)
Clutch palte warpage
Cylinder I . D .
Cylinder out of round
Cylinder taper
Cylinder warpage
Piston mark direction
Piston O . D . ( D )
Piston O . D . measurement point
Piston pin hole O . D . (d)
Cylinder-to-piston clearance
Piston pin O . D .
Piston-to-piston p i n clearance
Connecting rod-to-piston clearance
Top ring-to-ri ng groove clearance
Second ring-to-ring groove clearance
Top ring end gap
Second ring end gap
Oil ring (side ra i l ) end gap
Top ring mark
Second ring mark
Crankshaft
Connecting rod small end I . D .
Connecting rod big end side clerance
rad ial clearance
G)
Crankshaft ru nout
Crankpin oil clearance
Connecting rod bearing selection
Main journal oil clearance
Main journal bearing selection
1- 8
Item
(H)
d
D
Standard
10-20 (0.4-0.8)
24.995-25.012 (0.9841-0.9847)
44.4 (1. 75)
2.92-3.08 (0.115-0.121)
2.92-3.08 (0.115-0.121)
--
70.000-70.015 (2. 755-2. 756)
--
--
--
With "IN" mark facing to the intake side
69.970-69.990 (2. 755-2. 756)
10 (0.4)
17.002-17.008 (0.6694-0.6695)
0.010-0.035 (0.0004-0.0014)
16.994-17.000 (0.6691-0.6693)
0.002-0.014 (0.0001-0.0005)
0.016-0.040 (0.0006-0.0016)
0.015-0.050 (0.0006-0.0019)
0.015-0.045 (0.0006-0.0018)
0.20-0.35 (0.008-0.014)
0.35-0.50 (0.014-0.020)
0.20-0.80 (0.008-0.031)
I nstal l with the marked side u p
I nstal l with the marked side u p
17.016-17.043 (0.6699-0.6706)
0.10-0.30 (0.004-0.012)
0.030-0.052 (0.0012-0.0020)
11-9
See page
0.019-0.037 (0.0007 -0.0015)
11-8
See page
Unit: mm (in)
Service Limit
--
25.08 (0.987)
41.2 (1.62)
2.5 (0.10)
2.5 (0.10)
--
70.10 (2. 759)
0. 1 0 (0.004)
0.10 (0.004)
0.10 (0.004)
--
69.85 (2. 750)
--
17.02 (0.670)
--
16.98 (0.669)
--
--
0.10 (0.04)
0. 1 0 (0.004)
0.5 (0.02)
0.7 (0.03)
1.00 (0.039)
--
--
17.04 (0.671)
0.40 (0.016)
0.05 (0.002)
0.08 (0.003)
0.05 (0.019)