Pioneer VSX-S510-k Operating Instructions Manual page 24

3 3
• Press at any time to exit the Home
HOME MENU
Menu. If you cancel the Auto MCACC setup at any
time, the receiver automatically exits and no settings
will be made.
• The screensaver automatically starts after three
minutes of inactivity.
6
Select 'Auto MCACC' from the Home Menu, then press
ENTER.
Home Menu Home Menu
1 . Au to MC ACC 1 . Au t o M CACC
2 . Manu al SP Se tu p 2 . Ma nua l SP S et up
3 . I npu t A ssign 3 . In p ut Ass ig n
4. Auto Power Down 4. Au t o Power Down
5. HD MI Set u p 5. HDMI Se tu p
6. Ne two rk St an dby
7. MHL Set u p
8. Sp eaker Syst em
9. OSD Set u p
VSX-S510 VSX-S310
• Mic In! blinks when the microphone is not connected
to MCACC SETUP MIC jack.
Try to be as quiet as possible after pressing ENTER. The
system outputs a series of test tones to establish the
ambient noise level.
7
Follow the instructions on-screen.
• Make sure the microphone is connected.
• Make sure the subwoofer is on and the volume is
turned up.
• When using surround back speakers, turn on the
power to the amplifier to which the surround back
speakers are connected, and adjust the sound level to
the desired level (VSX-S510 only).
8
Wait for the test tones to finish.
A progress report is displayed on-screen while the
receiver outputs test tones to determine the speakers
present in your setup. Try to be as quiet as possible while
it's doing this.
1 . Auto MC ACC
N ow An aly z i ng
E nv i ronme nt Ch e ck
A mbi e nt No is e
S pe a k er Y E S / N O
R e tu rn
• For correct speaker settings, do not adjust the volume
during the test tones.
9
Confirm the speaker configuration.
The configuration shown on-screen should reflect the
actual speakers you have.
1 . Auto MCACC 1 . Auto MCACC
Check
Front [ YES ] Front
Center [ YES ] Center
[ YES ]
Surr Surr
Surr. Back [YESx2] Subwoofer
Subwoofer [ YES ]
OK
10:Next 10:Next
Return
VSX-S510
• With error messages (such as Too much ambient
noise) select RETRY after checking for ambient noise
(see Other problems when using the Auto MCACC
setup below).
If the speaker configuration displayed isn't correct, use
/ /
to select the speaker and
setting. When you're finished, go to the next step.
If you see an error message (ERR) in the right side
column, there may be a problem with the speaker
connection. If selecting RETRY doesn't fix the problem,
turn off the power and check the speaker connections.
24
10
Make sure 'OK' is selected, then press ENTER.
If the screen in step 9 is left untouched for 10 seconds
and
ENTER
setup will start automatically as shown.
A progress report is displayed on-screen while the
receiver outputs more test tones to determine the
optimum receiver settings for channel level, speaker
distance, X.Over, and Acoustic Calibration EQ.
Again, try to be as quiet as possible while this is
happening. It may take 1 to 3 minutes.
11
The Auto MCACC setup has finished! You return to the
Home Menu.
The settings made in the Auto MCACC setup should give
Check
[ YES ]
you excellent surround sound from your system, but it is
[ YES ]
[ YES ] also possible to adjust these settings manually using the
[ YES ]
Home Menu (starting on
OK Note
Return
• Depending on the characteristics of your room, sometimes
VSX-S310
identical speakers with cone sizes of around 12 cm will end
up with different size settings. You can correct the setting
manually using the
• The subwoofer distance setting may be farther than the
actual distance from the listening position. This setting
should be accurate (taking delay and room characteristics
to change the
into account) and generally does not need to be changed.
Basic Setup
is not pressed in step 10, the Auto MCACC
1 . Auto MCAC C
Now A na ly z ing
S urro un d A na ly z ing
S p e a k er Sy s te m
X .Ov e r
S p e a k er Dis ta n c e
C ha n n e l L ev e l
A c ou s tic Ca l E Q
Return
page 51).
Speaker Setting on page 51.
4
7
58