Yamaha QL5 Reference Manual page 216

Message
Monitor Assignment is Restricted to The Monitor Define function allows a maximum of eight sources to
Max. 8 Sources! be selected, but you attempted to assign more than eight.
In the RECORDER screen, it is not possible to move to a level higher
No Access From Recorder!
than \YPE\SONGS\.
No Channel Selected. A copy-source channel was not selected in the GLOBAL PASTE screen.
In the GLOBAL PASTE screen, you attempted to paste without having
No Copy Item Selected.
selected an item to paste.
No Corresponding Help Items. The corresponding section was not found in the Help file.
No ID3 Tag exists. You can not edit. The music file cannot be edited because it has no ID3 tag.
No Response from External HA. No response from an external AD8HR.
No Response from I/O DEVICE. The I/O devices not responding.
Operating as the word clock master. The QL series is operating correctly as a word clock master.
Page Bookmarked. The current screen or popup has been bookmarked.
Parameter out of range! Some data could not be loaded because of a parameter mismatch.
Password Changed. The password has been changed.
Audio file link playback is not possible because recording is in
PlayBack Failed: Recorder is Busy!
progress.
CUE was canceled for PLAYBACK OUT because you switched from the
PLAYBACK OUT CUE: Turned Off.
RECORDER screen to another screen.
Please use Dante Controller. DANTE PATCH settings from the console are not enabled.
Please wait, Dante patch is proceeding You attempted to edit in the DANTE PATCH screen at a time when
now. patching was not possible.
The cooling fan of the internal power supply has stopped. Please
Power Supply Fan has Malfunctioned! contact your Yamaha service center listed at the end of the Owner's
Manual (separate document).
PREVIEW Mode : Cannot Use This The operation was ignored because this function cannot be used
Function. during Preview.
PREVIEW Mode : Disabled Preview was disabled.
PREVIEW Mode : Enabled Preview was enabled.
Processing Aborted. Processing was interrupted.
Operation of the button was canceled because time is required for
Recorder Busy: Operation Aborted!
recorder processing.
RECORDER: CODEC Error [0x%08X] ! A codec error occurred in the RECORDER screen.
CUE was canceled for RECORDER IN because you switched from the
RECORDER IN CUE: Turned Off.
RECORDER screen to another screen.
When specifying the user password, the password was not entered a
Re-Enter Password!
second time.
REMOTE: Data Framing Error!
An inappropriate signal has been input to the Remote connector.
REMOTE: Data Overrun!
REMOTE: Rx Buffer Full! Too much data has been received at the Remote connector.
REMOTE: Tx Buffer Full! Too much data has been transmitted from the Remote connector.
Removed from the Channel Link group. The channel was removed from the link group.
Meaning
216
Message
Saving Aborted. Saving to the USB flash drive has been interrupted.
Saving Finished. Finished saving to USB flash drive.
No data has been stored in the scene you attempted to recall, or the
SCENE #xxx is Empty!
data has been damaged so that it cannot be recalled.
SCENE #xxx is Protected! You attempted to overwrite (store) a protected scene.
SCENE #xxx is Read Only! You attempted to overwrite (store) a read-only scene.
Scene Playback Link Canceled! The audio playback link for the scene was canceled.
SLOT x: Data Framing Error!
Invalid signals are being input to the SLOT x input port.
SLOT x: Data Overrun!
SLOT x: Rx Buffer Full! Too much data is being received at the SLOT x input port.
SLOT x: Tx Buffer Full! Too much data is being transmitted from the SLOT x output port.
Some songs were not identified. Songs that have not been specified
Some Song Files Are Unidentified.
might be used for DIRECT PLAY or SCENE PLAY BACK LINK.
The file specified for SCENE LINK or DIRECT PLAY assigned to a USER
Song File Not Found!
DEFINED key does not exist.
STAGEMIX: Data Framing Error!
Invalid signals are being exchanged with StageMix.
STAGEMIX: Data Overrun!
STAGEMIX: Rx Buffer Full! Too much data is being received at the StageMix input port.
STAGEMIX: Tx Buffer Full! Too much data is being transmitted from the StageMix output port.
The file could not be saved because there is insufficient space on the
Storage Full!
USB flash drive.
Storage Not Found! The USB flash drive could not be recognized.
Storage Not Ready! Access is not possible because the USB flash drive is not ready.
Sync Error! [xxx] The QL series console is not synchronized to the [xxx] signal.
Tap operation was ignored because the TAP TEMPO button is not
Tap Operation Ignored.
displayed in the screen.
This operation has been ignored because the current user does not
This Operation is Not Allowed.
have permission.
You attempted to open a bookmark or window that does not exist in
This page does not exist in this model.
the QL series.
Loading is not possible because the bitmap file is too large. The
maximum supported file size is 307,256 Bytes.
Too Large Files! Loading Failed.
Or loading is not possible because the bitmap file is too large. The
maximum supported file size is 1024 kilobytes.
Too Many Bands Used! Cannot Copying 31BandGEQ and comparing it to Flex15GEQ has failed
Compare. because more than 15 bands are included in the copy source.
Too Many Bands Used! Cannot Paste to Copying and pasting 31BandGEQ to Flex15GEQ has failed because
Flex15GEQ. more than 15 bands are included in the copy source.
Power consumption of the I/O cards installed in the slots has
Total Slot Power Capability Exceeded!
exceeded the rated value.
Your operation has been ignored because there is no parameter that
Unassigned Encoder.
corresponds to the knob you operated.
Unit Fan has Malfunctioned The fan of the R series has malfunctioned.
Warning/Error Messages
Meaning
Reference Manual