Table of Contents
Advertisement
Instruction manual: CITIZEN Eco-Drive Proximity
Disconnecting with iPhone
You can close the connection with the iPhone in the following cases:
• When the function hand on the upper right sub dial indicates "ON"
area.
• When the watch mode is set to [TME], [L-TM], [PR] or [CT].
• When the second hand indicates the second.
(While the second hand indicates a notification type, stop the
notification indication by pressing and holding either the lower right
button
or upper right button
for two seconds.)
1
Press and hold the upper right button
for seven seconds
or more.
The connection is closed and the function hand on the
upper right sub dial points the "OFF" area.
• To close connection from the iPhone, slide the switch of
"Proximity Connect" to "OFF". The switch name changes
to "Scan".
Proximity Connect
Scan
OFF
You can also close connection by changing the
mode of the watch.
1
Change the mode to [DCT].
The connection is closed and the
function hand on the upper right
sub dial indicates "OFF" area.
• In this case, the switch name
changes from "Proximity Connect"
to "Waiting for Reconnection".
Waiting for Reconnection
2
Change the mode to either [TME] (or [L-TM]) to
(See page 3b.)
finish the procedure.
Checking the connection status on the app screen
While
You can use the functions with
Proximity Connect
ON
the setting "ON".
connected
Only the following operations
Waiting for Reconnection
ON
are available:
• Reconnection with the
Shown when the
operation on the watch (see
disconnection is done by
page 6b)
the watch operation or
• Searching for your iPhone (see
intentionally. In this case, you
page 7a)
Disconnected
cannot register the iPhone.
It is recommended to stop or
Scan
ON
quit the app to save the batteries
Shown when the
of the watch and/or the iPhone
disconnection is done by the
when leaving them disconnected
app operation.
for a long time.
• The Bluetooth setting on the
Scan
OFF
iPhone remains "ON" even
App in rest
when "Scan" is set to "OFF"
The app does not consume the
or the app is not active.
iPhone battery.
a
[DCT]
Connecting to the registered iPhone
You can reconnect with the registered iPhone again in the following
cases:
• When the function hand on the upper right sub dial indicates "OFF"
area.
• When the watch mode is set to [TME], [L-TM], [PR] or [CT].
• When the second hand indicates the second.
(While the second hand indicates a notification type, stop the
notification indication by pressing and holding either the lower right
button
or upper right button
1
Confirm the switch of "Scan" or "Waiting for Reconnection"
is "ON" on the app's screen.
2
Press and release the upper right button
Function hand
The second hand moves to indicate "ACT". When
on the upper
successfully connected, the movement of the second hand
right sub dial
returns to normal and the function hand on the upper
right sub dial indicates "ON" area.
ON
• It may take up 20 to 30 seconds to complete the
reconnection.
(See page 3b.)
Function hand
on the upper
right sub dial
ON
[CT]
for two seconds.)
.
Function hand
on the upper
right sub dial
You can also reconnect the watch and the iPhone
by changing the mode of the watch.
1
Change the mode to [CT].
(See page 3b.)
The second hand moves to indicate
"ACT".
When successfully connected, the
Function hand
movement of the second hand
on the upper
returns to normal and the function
right sub dial
hand on the upper right sub dial
indicates "ON" area.
• It may take up 20 to 30 seconds to complete the
reconnection.
2
Change the mode to either [TME] (or [L-TM]) to
(See page 3b.)
finish the procedure.
b
Activating the functions of the dedicated app
You can set functions to "ON" or "OFF" on the app's screen during
connection. For the details of each function, refer to the pages shown
below.
Function
Page
Description
6c Sends time/calendar info.
Time Sync
6c Sends notification of incoming call.
Incoming Call
7a Sends notification of schedule from the built-in
Schedule Alert
Calendar app on the iPhone.
7b Sends notification of email reception for the account
Email Alert
registered to the app.
7a Notifies when the connection is interrupted.
Bluetooth Link
Loss Alert
7a Makes the iPhone sounding to answer the signal from
iPhone Search
the watch.
Automatic adjustment of time and calendar [Time sync]
When you set "Time Sync" to "ON", the watch receives the time info
(year, month, date, day, hour, minute, second) from the iPhone and
adjust the time following it each time they are connected.
Time Sync
ON
• The time on the watch is adjusted automatically each time they are
connected and the time setting of your iPhone is changed during
connection.
• The local time (see page 9a) is also adjusted based on the time
difference set as the time is adjusted.
• If the watch cannot receive the time information from the iPhone, a
message will appear on the iPhone.
• This watch keeps ±15-second monthly accuracy even if no time info
is received.
Receiving the time info manually
You can receive the time info manually by pressing and holding the
lower right button
for 2 seconds. Time info reception is executed
when the mode is [TME], [L-TM], [PR] or [CT] and the second hand
indicate second.
Receiving incoming call notification [Incoming Call]
When you set "Incoming Call" to "ON", the watch receives incoming
call info from the iPhone connected.
Incoming Call
ON
When receiving incoming call info
The watch vibrates twice and the second hand points "CALL".
• To return the second hand to normal movement, press and hold
either the lower right button
or upper right button
seconds.
c
6
for two
Hide quick links:
Advertisement
Table of Contents
