Using Local Time [L-Tm]; Using The Chronograph [Chr]; Checking And Correcting The Reference Position [302] - Citizen Eco-Drive Proximity Instruction Manual

Instruction manual: CITIZEN Eco-Drive Proximity
Using local time
Indicating local time (secondary time)
The watch can indicate the time of another time zone (known as local
time) using [L-TM] mode.
1
Change the mode to [L-TM].
The currently set local time (secondary time) is
displayed.
• The hour, minute, 24-hour, date and day of week are
displayed.
• If a local time (secondary time) has not been set, the
time reflected will be that of the time set in [TME]
mode.
• If you receive the time info while in [L-TM]
mode, both the time set in [TME] and [L-TM]
mode are adjusted.
Setting the local time
The setting range of the time difference from the time set in [TME]
mode is ±27 hours in 15-minute increments.
1
(See page 3b.)
Change the mode to [L-TM].
2
Pull the crown out to position .
3
Rotate the crown to set the time in 15-minute increments.
• When you rotate the crown quickly a few times, the hands will move
continuously. To stop the rapid movement, rotate the crown in either
direction.
4
Push the crown in to position to finish the procedure.
Using the chronograph
The 60-minute chronograph can indicate a maximum of 59
• While in [CHR] mode, notifications will be through watch vibration
only. Visual notification by the second hand is disabled in this mode
and will be made with another vibration when you change the mode
to [TME], [L-TM], [PR] or [CT].
1
Change the mode to [CHR].
The second hand moves to indicate the 0 seconds
position to enable you to measure time.
2
Use the chronograph.
• See page 9b for the method of measurement.
3
Change the mode to either [TME] (or [L-TM]) to
exit chronograph [CHR] mode.
a
[L-TM]
Second hand:
This indicates
the elapsed
seconds while
using the
(See page 3b.)
chronograph.
• After one hour of continuous chronograph operation, the
chronograph automatically stops and is reset. Pulling out the crown
will also stop and reset the chronograph.
• The time reflected by the hour and minute hands and 24-hour hand
on the upper left sub dial will be that of the time set in [TME] or
[L-TM] mode.
Checking and correcting the reference position [ 3 0 2 ]
If the time or date is not shown correctly even after proper reception
of the time info, check whether the reference position is correct.
What is the reference position?
The base position of all hands and
date to properly indicate the various
functions of this watch.
• Position of the hour hand: 12:00
• Position of the minute hand: 12:00
• Position of the second hand: 12:00
[CHR]
• Position of the 24-hour hand on the
59 . upper left sub dial: 24:00
' "
• Position of date: midway between 31
and 1
• Position of the function hand on
the upper right sub dial: directed
(See page 3b.) towards 6:00
• If the hands and/or date do not reflect the correct reference
position, the time, date, and other indications will not be displayed
accurately, even if you synchronize the time with your iPhone.
(See page 3b.)
Checking the reference position
Upper right button :
Start/Stop/Restart
Check whether the reference position of each hand and indication is
measurement.
accurate.
The chronograph
minute hand: This
indicates the elapsed
minutes (up to 60) while
using the chronograph.
Lower right button :
Reset
• Press and release this
button to reset the
chronograph after
timing.
Correct the current reference position
Correct each hand and indication to indicate the correct reference
position.
Correct reference positions
b
1
(See page 3b.)
Change the mode to [302].
The hands and date will rotate to the current
reference positions stored in memory.
2
Check the current reference position.
By referring to the chart on page 9b, ensure the
reference position of each hand and the date are
correct.
• If all reference positions are correct, go to step 3
below.
• If some reference positions are incorrect, go to page
9c.
3
Change the mode to either [TME] (or [L-TM]) to
(See page 3b.)
finish the procedure.
1
(See page 3b.)
Change the mode to [302].
Each hand and indication indicate the current
reference position.
2
Pull the crown out to position .
This will enable you to correct the reference
position.
3
Press and release the upper right button .
Each time you press and release the upper right
button , the active hand will move slightly
indicating that hand (or date) may be set. The
order of movement is:
Date/Function hand Hour, minute and 24-
hour hand Second hand return to date/
function hand
4
Rotate the crown to correct the reference position
of the active hand/indication.
• When you rotate the crown quickly a few times, the
hands and indications will move continuously.
The second hand will move one full rotation,
and the other hands and indications will move
until you rotate the crown either clockwise or
counterclockwise.
5
Repeat steps 3 and 4 as required.
6
Push the crown in to position .
7
Change the mode to either [TME] (or [L-TM]) to
(See page 3b.)
finish the procedure.
c
9