Figure 3-1. Removable I/O Section - Eaton Powerware 9315 Installation Manual

Installing the UPS
See Figure 3-1 before installing the UPS cabinet. The UPS cabinet base is equipped with
forklift slots to accommodate lifting and moving the equipment. The forklift slots are
located on all four sides of the cabinet base to meet individual needs. The wireway section
on the right side of the UPS cabinet (as seen from the front) must be removed to gain
access to the right side fork lift slots (see Figure 3-1).
Ó Ó Ó
Ó Ó Ó Ó Ó Ó
Ó Ó Ó Ó Ó Ó Ó Ó Ó
Ó Ó Ó Ó Ó Ó Ó Ó Ó
Ó Ó Ó
Ó Ó Ó
1. Move UPS to final installed location using forklift jacks between foam cushions on
2. Remove hardware labeled 1," 2," and 3" in Figure 3-2, holding the front, rear,
3. Remove the front, rear, and side supports from the cabinet base and foam
Lift only at forklift openings or cabinet damage may occur.
4. Insert the forklift jacks in the forklift slots and raise the UPS cabinet until the
3−2
EATON Powerware
Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó
Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó
Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó
Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó
Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó
Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó Ó
Ó Ó Ó Ó Ó Ó Ó Ó Ó
Ó Ó Ó
Ó Ó Ó
Removable
I/O Section
Behind Door

Figure 3-1. Removable I/O Section

the bottom of the unit.
and side supports to the cabinet base.
cushions. Discard or recycle the hardware and support brackets in a responsible
manner.
cabinet bottom clears the foam cushions by approximately 3 mm (1/8").
9315 UPS (300–500 kVA) Installation Manual S 164201118 Rev H www.powerware.com
®
Ó Ó Ó Ó
Ó Ó Ó Ó Ó Ó Ó Ó
Ó Ó Ó Ó Ó Ó
Ó Ó Ó Ó Ó Ó
Ó Ó Ó Ó Ó Ó
Ó Ó Ó Ó Ó Ó
Ó Ó Ó Ó Ó Ó Ó Ó
Ó Ó Ó Ó Ó Ó
Ó Ó Ó Ó Ó Ó
C A U T I O N
Hidden
Forklift
Slots
Do Not Lift