Toshiba RAS-M10YKV-E Service Manual page 42

9-2. Indoor Unit
Hanger
Hanger
Front cabinet Clip anchor
(local part)
Front panel
Hanger
5 Pan head
wood screw
7 Deodorizing
filter
4 Remote
control
6 Purifying
2 Wireless
holder
filter
remote
control
Before installing the wireless remote control
Wireless remote control 2
Batteries
3
• With the remote control cover opened,
Cover
load the supplied batteries correctly,
observing their polarity.
9-2-1. Accessory and Installation Parts
Part
Name of parts (Q'ty)
No.
1
Installation plate x 1
2
Wireless remote control x 1
3
Battery x 2
4
Remote control holder x 1
5
Pan head wood screw Ø3,1x 16 x 2
For the rear left and left piping
Wall
1 Installation
plate
Insert the something by fist-size between
the indoor unit and wall, and lift indoor
unit to make work easier.
Do not allow the drain hose to get slack.
Cut the piping hole
sloping slightly
Mounting
9
screw
Make sure to run the drain hose sloped
downward.
Shield pipe
The auxiliary piping can be
(local part)
connected the left, rear left, rear,
right or bottom.
Right
Rear
Bottom
Rear left
Insulation of refrigerant pipes insulates the pipes
separately, not together.
Use 6-mm thick heat resisting polyethylene foam
(Inside of the ceiling).
Use 10-mm thick heat resisting polyethylene foam
outside of the room.
Part
Name of parts (Q'ty)
No.
6
Purifying filter x 1
7
Deodorizing filter x 1
B
8
B Label x 2
9
Mounting screw Ø4 x 25 x 6
10
Indoor unit Installation manual x 1
9-2-2. Installation Place
• A place which provides the spaces around the
indoor unit as shown in the installation diagram.
• A place where there is no obstacle near the air
inlet and outlet.
• A place which allows an easy installation of the
piping to the outdoor unit.
• A place which allows the front panel to be
opened.
CAUTION
• Direct sunlight to wireless receiver of the
indoor unit should be avoided.
• The microprocessor in the indoor unit should
not be too close to r-f noise sources.
Remote Control
• A place where there are no obstacles such as a
curtain that may block the signal from the remote
Left
control.
• Do not install the remote control in a place
exposed to direct sunlight or close to a heating
source, such as a stove.
• Keep the remote control at least 1 m apart from
the nearest TV set or stereo equipment.
(This is necessary to prevent image distur-
bances or noise interference.)
• The location of the remote control should be
determined as shown below.
7m
Fig. 9-2-1
9-2-3. Cutting a Hole and Mounting
Installation Plate
Cutting a Hole
The center of the piping slot
is above the arrow.
The center of the pipe
hole is above the arrow.
Pipe hole
80mm
Fig. 9-2-2
1. After determining the pipe hole position on the
mounting plate (80 mm ), drill the pipe hole
(ø65 mm) at a slight downward slant to the
outdoor side.
NOTE :
• When drilling the pipe hole in the wall that the a
metal lath, wire lath or metal plate covers
inside, be sure to use a pipe hole brim ring sold
separately.
• There may be a wire conduit embedded in
the wall. Check on the blueprint or ask the
builder whether it is done or not.
• Make sure of the proper installation of the
installation plate before mounting the indoor
unit.
Mounting the Installation Plate
For installation of the indoor unit, use the paper
pattern on the back.
Anchor bolt hole
40mm
66mm
120mm
65,5mm
65,5mm
Pipe
hole
Pipe hole 1
Installation
Thread
9 Mounting plate
Indoor unit
screw
Weight
Fig. 9-2-3