Specifications - Integra DTR-8.3 Instruction Manual

Specifications

AMPLIFIER SECTION
Continuous average power output (FTC)
All channels:
Continuous power output (DIN)
Maximum power output (EIAJ)
Dynamic power output (stereo)
Total Harmonic Distortion:
IM Distortion:
Damping factor:
Input sensitivity and impedance
PHONO:
LINE (CD, TAPE, DVD,
VIDEO 1-5):
MULTICHANNEL INPUT
(FRONT L/C/R, SURROUND
L/R, SURROUND BACK L/R): 200 mV, 50 kΩ
(SUBWOOFER):
COAXIAL 1, 2, 3 (DIGITAL):
DVD, VIDEO 1, 2, 3, 4, 5:
COMPONENT VIDEO 1, 2:
Output level and impedance
Rec out (TAPE, VIDEO 1, 2):
Pre out:
ZONE 2 OUT:
VIDEO (VIDEO 1, 2, MONITOR
OUT, ZONE 2 OUT):
S-VIDEO (VIDEO 1, 2, MONITOR
OUT):
COMPONENT VIDEO OUT:
Phono overload:
Frequency response:
RIAA deviation:
Tone Control
Bass:
Treble:
Signal-to-noise ratio (direct)
Phono:
CD/Tape:
86
110 W per channel min. RMS at 8
Ω, 2 channels driven from 20 Hz to
20 kHz with no more than 0.08%
total harmonic distortion.
145 W min. RMS at 6 Ω, 2 channels
driven from 1 kHz with no more
than 0.1% total harmonic
distortion.
150 W at 6 Ω
180 W at 6 Ω
2 × 280 W at 3 Ω
2 × 220 W at 4 Ω
2 × 140 W at 8 Ω
0.08% at rated power
0.08% at 1 W output
0.08% at rated power
0.08% at 1 W output
60 at 8 Ω
2.5 mV, 50 kΩ
200 mV, 50 kΩ
36 mV, 50 kΩ
0.5 Vp-p, 75 Ω
1 Vp-p, 75 Ω
1 Vp-p, 75 Ω (Y)
0.28 Vp-p, 75 Ω (C)
1 Vp-p, 75 Ω (Y)
0.7 Vp-p, 75 Ω (P
, P )
B R
200 mV, 470 Ω
1 V, 470 Ω
100 mV, 470 Ω
1 Vp-p, 75 Ω
1 Vp-p, 75 Ω (Y)
0.28 p-p, 75 Ω (C)
1 Vp-p, 75 Ω (Y)
0.7 Vp-p, 75 Ω (P
, P )
B R
120 mV RMS at 1 kHz, 0.5% T.H.D.
5 Hz to 100 kHz : +1/–3 dB
(CD in Direct mode)
20 Hz to 20 kHz : ±0.8 dB
±10 dB at 50 Hz
±10 dB at 20,000 Hz
80 dB (IHF A, 5 mV input)
110 dB (IHF A, 0.5 V input)
TUNER SECTION
FM
Tuning range
USA & Canadian models:
Australian models:
Usable sensitivity
Mono:
Stereo:
50 dB quieting sensitivity
Mono:
Stereo:
Capture ratio:
Image rejection ratio
USA & Canadian models:
Australian models:
IF rejection ratio:
Signal-to-noise ratio
Mono:
Stereo:
Alternate channel attenuation:
Selectivity:
AM suppression ratio:
Total harmonic distortion
Mono:
Stereo:
Frequency response:
Stereo separation:
AM
Tuning range
USA & Canadian models:
Australian models:
Usable sensitivity:
Image rejection ratio:
IF rejection ratio:
Signal-to-noise ratio:
Total harmonic distortion:
GENERAL
Power supply
USA & Canadian models:
Australian models:
Power consumption
USA & Canadian models:
Australian models:
Dimensions (W × H × D):
Weight
Specifications and features are subject to change without notice.
87.50–108.00 MHz (100-kHz steps)
87.50–108.00 MHz (50-kHz steps)
11.2 dBf, 1.0 µV (75 Ω IHF)
0.9 µV (75 Ω DIN)
17.2 dBf, 2.0 µV (75 Ω IHF)
23 µV (75 Ω DIN)
17.2 dBf, 2.0 µV (75 Ω)
37.2 dBf, 20 µV (75 Ω)
2.0 dB
40 dB
85 dB
90 dB
76 dB
70 dB
55 dB
50 dB (DIN)
50 dB
0.2%
0.3%
30 Hz–15 kHz, ±1.0 dB
45 dB at 1 kHz
30 dB at 100 Hz–10 kHz
530 to 1,710kHz (10kHz steps)
522 to 1,611 kHz (9-kHz steps)
30 µV
40 dB
40 dB
40 dB
0.7%
AC 120 V, 60 Hz
AC 230–240 V, 50 Hz
8.4 A
670 W
435 × 175 × 460 mm
17-1/8" × 6-7/8" × 18-1/8"
18.2 kg (40.1 lbs)