Installation Instructions Location; Filter Cartridges - Marquis 660 Owner's Manual

E V E R Y D A Y H O T T U B S
INSTALLATION INSTRUCTIONS
LOCATION
For your portable spa to function properly and safely, it must be located on a
hard, flat, level surface. Inground spas require special installation techniques
and should be planned in conjunction with your authorized Marquis Spas
dealer. Improper installation can result in structural damage to the spa and the
voiding of your spa warranty. Items to discuss with your dealer include: local
construction codes, electrical service requirements, serviceability of equipment,
existing underground obstructions such as gas, water, and telephone lines,
safety measures such as fences and locks, and visibility of the spa installation
from the home, street, and neighbours.
• Do not shim your spa. If your pad is not level you must pour a top cap:
contact a professional.
• Allow for sufficient water drainage around the spa to help preserve the
equipment and support structure. This includes indoor installations.
• A filled spa can weigh up to 2268 Kg and the location must support the
weight of the filled spa.
• Locate the equipment compartment where it will be accessible. Your spa
MUST be installed to permit access for servicing the equipment above and/or
below any decks or floors. Access is essential and must allow adequate room
for service. To facilitate repairs, Marquis Corp. or its agent may require
access to spa equipment. It is your responsibility to provide unencumbered
access. See spa diagrams for location of power supply.
• Leave access to the circuit breakers in the sub panel.
• Be sure the spa is level and in the final position BEFORE filling with water.
Check for power cords, tools, and hoses that may be caught underneath the
spa.
• Do not apply power to the spa before it is completely filled with water.
Damage to the pumps, heater and sensors may result.
• IMPORTANT: DO NOT LET AN EMPTY SPA REMAIN EXPOSED TO
DIRECT SUNLIGHT. Spa surface temperatures can reach in excess of 82°C
if left exposed to the sun. Significant damage can occur if this is allowed to
happen, including warping and blistering of the surface and components.
Damage that occurs as a result of this exposure is not covered under the
warranty.
• CAUTION: Never try to move a spa that has not been fully drained. To do so
could result in damage to the spa and physical injury to the mover.
• Cracks in the spa surface, exterior siding or DuraBase due to improper
transport or support of the spa are not covered under the warranty.
OUTDOOR AND PATIO INSTALLATION
To install the spa outdoors, we recommend a reinforced concrete pad at least 10
cm thick. The reinforcing material should be grounded per electrical codes.
If you place the spa on the ground, even temporarily, place the spa empty of
water on concrete pavers under the entire bottom of the spa. The concrete
pavers should be at least 5 cm thick and level across the entire surface. The spa
will inevitably settle and become out of level on this surface, thus it is important
to get the spa onto a solid foundation as soon as possible.
INSTRUCTIONS FOR PREFABRICATED SPA PADS
If you are using a prefabricated spa pad for a foundation, please use the fol-
lowing guidelines:
1. Designate the area where the spa is to be installed. Please make sure the
ground is flat and level.
2. Using 2"x 6" weather resistant lumber and 3" outdoor deck screws, build a
frame large enough for the prefabricated spa pad to fit inside with minimum
1" clearance on all sides.
3. Install the frame in the area that has been leveled.
4. Using pea gravel, please fill the frame to the top.
5. Lay a straight piece of lumber across the frame and level any high spots in
the gravel by pushing the straight lumber across the frame. Fill in any low
areas with more gravel and re-level using the straight piece of lumber.
6. Compact the gravel to make the surface is hard and flat. You may need to
add more gravel to bring the level back up to the top of the frame. If so,
please re-level and re-compact until you have a hard, flat level surface that is
even with the top of the frame.
7. Place the prefabricated spa pad on top of the gravel. Please be careful not to
disturb the hard, flat, level surface.
®
®
O W N E R ' S
8. Please make sure no portion of the spa pad is sitting outside or on top of the
framing.
9. Place the spa on top of the pad and fill the spa with water.
DECK INSTALLATION
Be sure the deck can support the weight of your filled spa by checking the
deck's maximum load capacity. Consult a qualified building contractor or
structural engineer. Minimum requirement is 45.36 Kgs. per 9.3 cm.
Modular spa foundations may not be used to support the spa. Use of modular
foundations without proper preparation and installation can cause your spa to
settle over time and could cause the spa to crack. Cracks caused by lack of
support are not covered by warranty.
If you are using a prefabricated spa pad for a foundation, please follow
guidelines:
1. Designate spa installation area. Make sure the ground is flat and level.
2. Using 2"x 6" weather resistant lumber and 3" outdoor deck screws, build a
frame large enough for the prefabricated spa pad to fit inside with minimum
1" clearance on all sides.
3. Install the frame in the area that has been leveled.
4. Using crushed gravel, fill the frame to the top.
5. Lay a straight piece of lumber across the frame and level any high or low
spots. Re-level using the straight piece of lumber.
6. Compact gravel to make surface hard, flat and even with the top of the
frame.
7. Place prefabricated spa pad on top of the gravel. Don't disturb level surface.
8. Make sure no portion of the spa pad is sitting outside or on top of the
framing.
9. Place the spa on top of the pad and fill the spa with water.
INDOOR INSTALLATION
There are special requirements if you place your spa indoors. Flooring material
must provide adequate traction when wet. Proper drainage is essential to
prevent water pooling. To avoid increased humidity, you need to provide proper
ventilation to the area. The addition of a ventilation system is recommended.
SHUT-OFF VALVES
Your spa is equipped with shut-off valves (see EQUIPMENT DIAGRAM) that
shut off the water flow to the equipment system for authorized Marquis Spas®
dealer service. At times, a new spa or one that has recently been serviced may
have the shut-off valves partially closed which can restrict the water flow and hinder
jet performance. Be sure the valves are fully open.
FREEZE PROTECTION
When a freeze condition is detected (which occurs when the temperature in the
heater housing drops to 13°C), the jet pump(s) is automatically activated. In
areas with extremely cold winter conditions, your spa should be fine as long as it
is left running at normal operating temperatures. If you plan to turn the spa off,
follow the instructions in this manual (see SUSPENDED USE OR
WINTERIZING YOUR SPA).
OVERHEATING
In the case of extended hot weather, the spa water temperature may reach and
maintain 40°C to 41°C or higher. This is due to the ambient temperature and the
full insulation in the spa cabinet. You may have the option of shortening the
pump-run time. (See SPA CONTROL OPERATION for available options.)
FILTER CARTRIDGE(S)
Your portable spa features one or two Vortex filters.
Filter cartridges and filter lids are warranted to be free of defect at time of
delivery and do not qualify for labor coverage under the warranty. These parts
can be purchased or exchanged at your authorized Marquis Spas
NOTE: It is very important that the components of these filtration systems be
installed properly in the proper part of the spa.
M A N U A L
dealer.
®
3