Switching The Angle; Changing The Brightness Of The Display (Dimmer Control); Hdmi Control Function - Denon DVD-A1UDCI Owner's Manual

ENGLISH
Operations Enabled During Playback
2
Thrn the power on for all the equipment connected by
HDMI cable.
1
Set the HDMI output terminal corresponding with
the HDMI control function.
On the GUI menu, set "HDMI Setup" - "HDMI Control" (m:ff'page
26).
*
The HDMI control function will work only on one of the 2 HDMI
output terminals on the DVD-A 1UDCI.
3
Set the HDMI control function for all equipment
connected by HDMI cable.
On the GUI menu, set the DVD-A 1UDCI with "HDMI Setup"
- "HDMI Control" (m:ff'page 26).
*
Please refer to the owner's manual as regards setting of connected
devices.
*
Carry out Steps 2 and 3 should any of the equipment be
unplugged.
4
To ensure that the DVD-AIUDCI's HDMI video
output is projected on the TV screen, change the
input function of the TV and AV Amp.
5
When you turn the TV's power to standby, check that
the power of the DVD-AIUDCI and AV Amp also goes
on standby.
If the HDMI control function does not operate properly, check the
following points.
ols the TV or AV Amp compatible with the HDMI control function!
ols the setting of the DVD-A1UDCI's HDMI output terminal correct!
(Step 1)
oAre the HDMI control function settings of all equipment correct!
(Step 3)
oAfter setting, did you add another HDMI device connection or
make any changes in the connections? In this case, perform setting
again.
When you make an HDMI connection with a TV or AV Amp compatible
with DVD-A 1UDCI and HDMI control functions. you can perform the
following operations by setting the HDMI control function of each
device.
o
Operating the DVD-A1UDCI via the TV's remote
control.
(When the TV's remote control has player operation buttons)
o
Turning off the TV's power turns the DVD-A1UDCl's
power to standby.
HDMI Control Function
o
TV or AV Amp power is turned on by operating
the DVD-A1UDCI, and functions change with DVD-
A1UDCI input.
-¢'I»'.
oThe HDMI control function controls operations of a TV that is
compatible with the HDMI control function. Make sure that the TV
and HDMI are connected when you perform HDMI control.
oSome functions may not operate depending on the connected TV
or AV Amp. Check the owner's manual of each device for details
beforehand.
oWhen "Other Setup" - "Power Saving" on the GUI menu is set
to "Power Saving Standby" or "Normal Standby" (m:ff'page 32).
the player's power cannot be turned on using the HDMI control
function.
oWhen "HDMI Setup" - "HDMI Control" - "Power Off Control" on the
GUI menu is set to "Off" (m:ff'page 26). the DVD-AlUDCI is not set
to standby even if the connected device is in the standby mode.
oWhen "DENON LINK Setup" - "DENON LINK Mode" on the GUI
menu is set to "4th", the HDMI control function is enabled for the
connected devices.
0008
each time the button is
e
CD
e
G
8880
6~O
A~/\
L
Normal --. Dim --. Dark --. Off
~
Press(~l.
The display brightness
pressed.
1
Press
8
during playback.
The angle number currently being played is displayed.
2
Use <:I> <:::0 to select angle.
Changing the Brightness of the
Display (Dimmer Control)
3
Press 8.
The setup screen disappears.
During playback of a BD or DVD-Video recorded with several
camera angles, you can change the angle.
-Nln8
Angle changing may be restricted. depending on the disc.
I
Switching the Angle
Even when "Off" is selected. the status of operations that are
performed appears momentarily on the display if "Display Setup"
- "Temporary Display" on the GUI menu is set to "On" (m:ff'page 32).
49