Denon DVD-A1UDCI Owner's Manual page 32

ENGLISH
Audio Set...,
Setting items Setting contents Setting items
Setting contents
o
When outputting CD, etc. to a digital recording device such as the CD
recorder, convert to PCM or PCM down sampling.
o
When a disc with recorded Linear PCM or PPCM (Packed PCM) is played
back, this outputs Linear PCM irrespective of the setting.
Qa: Outputs BD effect sound.
Off: Does not output BD effect sound.
Au.tQ : Outputs primary audio (main audio) in the same type of audio
format. Dolby Digital/Dolby Digital Plus/Dolby TrueHD are output as
Dolby Digital, DTS/DTS-HD are output as DTS and Linear PCM is output
as Linear PCM.
Dolby Digital: Outputs to the digital audio output terminal (optical/
coaxial) with Dolby Digital.
DTS : Outputs to the digital audio output terminal (optical/coaxial) with
DTS.
#
Valid when "BD Audio Mode" is set to "Mix Audio Output" (&page
33)
BD Effect Sound
Sets for a click sound and
other outputs during BD
popup menu operations.
BD Re-Encoder
Sets the format during
output of the BD's Mix Audio
signal from the digital output
terminal.
Digital Out
Bitstream : Outputs a bitstream signal. Converts Dolby TrueHD, Dolby
Set the audio signal of digital Digital Plus to Dolby Digital, and DTS-HD to DTS for output
audio output. PCM : Output the downmixed audio signal to 2ch LPCM.
Formoreinformationoneach PCM Down Sampling: Convert sampling frequency audio greater than
audio signal. refer to 'Audio 48 kHz to a 48 kHz 2ch LPCM audio output signal.
Signal from the Digital Audio
#
Output (Optical/Coaxial)
Terminal" (@"page 17).
o
Setting "On: 50 kHz" or "On: 100 kHz" enables full-range playback on
all channels recommended for DTS. (Note that this results in a 5 dB
increase in subwoofer volume, and a 15 dB increase with Super Audio
CD) This also allows you to play back the 6-channel source of DVD-
Audio recorded on all channels with the full frequency range. In this
case, make an analog connection according to disc operating manual.
o
When set to "On. 50 kHz" or "On: 100 kHz", all speaker sizes are set to
"Large" and "Yes" is set for the subwoofer.
o
Even when set to "On: 50 kHz" or "On: 100 kHz", "Channel Level" and
"Distance" settings are available.
Off :
Enable the speaker and subwoofer settings.
On : 50kHz: Output the disc contents as is. When playing Super Audio
CD, output up to 50 kHz audio signals.
On : 100kHz: Output the disc contents as is. When playing Super Audio
CD, output up to 100 kHz audio signals.
Au.tQ : Automatically compress Dolby TrueHD audio dynamic range. The
sound is not compressed when playing signals other than Dolby TrueHD
signals.
Off : Dynamic Range compression is not applied.
Low: Set minimum dynamic range compression.
Middle: Set middle dynamic range compression.
High: Set maximum dynamic range compression.
Source Direct
Disable the speaker and
subwoofer settings and
output the disc audio as is.
#
Set to within the playback
frequency band of the
amplifier you are to use:
"On" at "50 kHz" or "100
kHz". Setting outside the
frequency band can result
in damage to your amplifier
and even fire.
Compression
Compresses the dynamic
range of Dolby TrueHD/
Dolby Digital/Dolby Digital
Plus audio. At night or other
times when you cannot play
back at high volume, this
compensates by reducing
high level sounds and
increasing low level sounds.
I
AFDM
Automatically set the
surround mode by detecting
the surround mode
identification signal recorded
in the disc.
On :
Automatically set surround mode when the ID signal is included.
Off: Do not set surround mode even when the ID signal is included.
MTRX : Create a surround audio signal by matrix processing, regardless
of the presence of an ID signal.
#
An EX flag may not be included for Dolby Digital EX sources. Even with
"AFDM" set to "On", set to "MTRX" in case the playback mode does not
automatically switch.
-N'U
a
o
This setting is valid when "Audio Setup" - "7.1 ch Audio Out" on the GUI
menu is set to "Multi-Channel" and when "HDMI Setup" - "Audio Setup"
on the GUI menu is set to "Multi LPCM BM On" (@"page 25).
o
This setting is invalid when "Audio Setup" - "Source Direct" on the GUI
menu is set to "On" (&page 29), and when "DENON LINK Setup" -
"DENON LINK Mode" is set to anything other than "Off" (&page 30).
o
This function is invalid for the DTS-CD source.
Downmix
Set the method used to
convert a multi-channel
audio signal to a 2-channel
signal.
LtLB1 :
Signals are converted to Dolby Surround compatible 2-channel
audio signals for output. This setting is valid for DTS-HD, DTS Digital
Surround, Dolby Digital Plus and Dolby Digital audio signals. (If the
connected AV Amp is Dolby Pro Logic compatible, AV Amp plays back
using surround audio.)
Stereo: Outputs by converting to the 2ch (stereo) audio.
-N,Oa
In order to enable the "Lt/Rt" setting when playing back BD, set "BD
Audio Mode" to "HD Audio Output" (lI2Fpage 33).
29
Remote control operation
buttons
.Displaying the menu
Cancel the menu
.Moves the cursor
'(Up/Down/Left/Right)
8
:Decision the setting
RETURN
(R)
:Return to previous menu