Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Interlogix NX-4V2
Summary of Contents for Interlogix NX-4V2
- Page 1 NX-4V2 LED Keypad User Manual P/N I-NX4V2-OM • REV C • NOV12...
- Page 2 © 2012 UTC Fire & Security Americas Corporation, Inc. Copyright Interlogix is part of UTC Climate Controls & Security, a unit of United Technologies Corporation. All rights reserved Trademarks and Other trade names used in this document may be trademarks or registered patents trademarks of the manufacturers or vendors of the respective products.
-
Page 3: Table Of Contents
Unbypassing 9 Turning the door chime ON and OFF 9 Adding and changing user codes 10 Assigning user code authority levels 11 Other keypad functions 11 Service menu 14 Emergency evacuation plans 16 System notes 17 NX-4V2 LED Keypad User Manual... - Page 4 NX-4V2 LED Keypad User Manual...
-
Page 5: Security System Notes
Exit Delay Time __________ Secondary Exit Delay Time ________ Entry Delay Time _________ Secondary Entry Delay Time _______ ZONE DESCRIPTIONS 01 _______________________ 05 _______________________ 02 _______________________ 06 _______________________ 03 _______________________ 07 _______________________ 04 _______________________ 08 _______________________ NX-4V2 LED Keypad User Manual... -
Page 6: Introduction
• It may be possible to arm the security system without the backup battery connected. Your periodic test should be done with A.C. Power removed to verify the battery is connected and adequately charged. NX-4V2 LED Keypad User Manual... - Page 7 PLEASE READ THE FOLLOWING INFORMATION AND INSTRUCTIONS CAREFULLY BEFORE OPERATING YOUR SECURITY CONTROL SYSTEM. IF YOU DO NOT UNDERSTAND ANY PORTION OF THIS MANUAL, OR IF YOU HAVE ANY QUESTIONS ABOUT YOUR SYSTEM, CONTACT THE INSTALLING COMPANY. NX-4V2 LED Keypad User Manual...
-
Page 8: Glossary Of Terms
[STAY] or [EXIT] key on the keypad control (for ARMING only) as programmed by the installing company. User Code A four (4) or six (6) digit entry code used to arm or disarm the system. NX-4V2 LED Keypad User Manual... -
Page 9: Understanding The Lights
Trouble conditions are: Tamper Hardware Low Battery Loss of supervision (A combination of Alarm/Fault and Tamper/Trouble will produce a rapid “flashing” light for a short period of time, followed by a slow “flashing” light.) NX-4V2 LED Keypad User Manual... -
Page 10: Emergency Activation Keys
The security system will not arm if the ready light is not on or flashing. • If the power light is off, you have no AC power. Restore power if possible. If not, contact your installing company for service. NX-4V2 LED Keypad User Manual... -
Page 11: Arming Your System In The "Stay Mode
Step 4 • To change entry/exit to “Instant”, press the [STAY] key again. • The instant light will illuminate indicating that the entry/exit doors have no delay. • To change entry/exit to “Delayed”, press the [STAY] key again. NX-4V2 LED Keypad User Manual... -
Page 12: Using The Quick Arm (Optional)
[CANCEL] key while this light is flashing, all abortable reports will stop the communication process. Note: The abort feature must be enabled. Entering a code followed by the [CANCEL] key during or after an alarm report to the central NX-4V2 LED Keypad User Manual... -
Page 13: Bypassing Zones
[CHIME] key. If the chime is on, the chime light will be illuminated. If the chime is off, the chime light will be off. Each press of the [CHIME] key will toggle the chime feature on/off and produce a momentary ding-dong sound. NX-4V2 LED Keypad User Manual... -
Page 14: Adding And Changing User Codes
3 times. 8. If another “user code” needs to be programmed, return to Step 5. 9. Press the [#] key while the ready light is flashing to exit the User Code Programming Mode. NX-4V2 LED Keypad User Manual... -
Page 15: Assigning User Code Authority Levels
- 6 until you have assigned authority levels to all user numbers. 7. Press the [#] key to exit the Assigning Authority Level Program. Other keypad functions Setting the keypad tone ∗ ]-[0]. Keypad is now in the “Adjust Tone” mode. 1. Press [ NX-4V2 LED Keypad User Manual... - Page 16 ]-[7]. Resets have now been performed. 3. If the keypad begins beeping, the reset did not execute properly. Enter your code to silence the keypad. Wait a few minutes and repeat step 2 to attempt NX-4V2 LED Keypad User Manual...
- Page 17 12:00 Midnight 8:00 AM 4:00 PM 1:00 AM 9:00 AM 5:00 PM 2:00 AM 10:00 AM 6:00 PM 3:00 AM 11:00 AM 7:00 PM 4:00 AM 12:00 Noon 8:00 PM 5:00 AM 1:00 PM 9:00 PM NX-4V2 LED Keypad User Manual...
-
Page 18: Service Menu
“on”, press the [∗] key followed by the [2] key to determine the service condition. One or more zone lights will illuminate indicating what service(s) is required. Call your service provider immediately for these problems. Below is a listing of what each light means in a service condition. NX-4V2 LED Keypad User Manual... - Page 19 LOSS OF SYSTEM TIME - This light will illuminate when there has been a loss of power and your system clock needs to be reset. Exit Press the [#] key to exit the Service Light mode. NX-4V2 LED Keypad User Manual...
-
Page 20: Emergency Evacuation Plans
National Fire Protection Association, Batterymarch Park, Quincy, MA 02269. The following are examples of evacuation plans. A plan unique to your home or business should be drawn and memorized by each occupant. NX-4V2 LED Keypad User Manual... -
Page 21: System Notes
System notes NX-4V2 LED Keypad User Manual...